Removing Mould from Grout in a Shower Cubicle

The photographs below are from the bathroom of a house in the Moston area of Manchester which is primarily residential and only 3 miles away from the city centre. My customer had been primarily concerned with the removal of unsightly mould but was also keen to have the grout in the ceramic tiled shower cubicle given a good deep clean.

Ceramic Tiled Shower Cubicle Before Restoration Moston Ceramic Tiled Shower Cubicle Before Restoration Moston

Cleaning a Ceramic Tiled Shower Cubicle

To clean the Shower Cubicle, I used a strong dilution of Tile Doctor Pro Clean which is a strong alkaline cleaner that works really well on grout. The Pro-Clean solution was decanted into a spray bottle and then sprayed onto the grout lines and left it to dwell. The air in the solution makes it lighter and easier for it to stick to vertical surfaces.

After a few minutes the Pro-Clean was scrubbed in using a stiff grout brush. The tiles were then rinsed with water to remove the soiled solution from the tiles and the process repeated where required.

Although cleaning process was a success there were still a few mould marks left so to tackle these I used Tile Doctor Mould Away spray using the same process of scrubbing and rinsing. The Mould Away spray did the trick for me and I moved on to remove the silicone around the shower cubicle. When removing silicone, you must make sure you get all mouldy silicone out otherwise it can spread from the old to the new.

Ceramic Tiled Shower Cubicle During Restoration Moston

After I had finished removing the silicone I tidied the shower cubicle and used a bit of gentle heat from my heat gun to dry the grout lines and edges where silicone used to be.

Grout Colouring a Ceramic Tiled Shower Cubicle

I used my damp tester to make ensure there was no dampness anywhere around the working area and then moved on to colouring the grout which would give the whole shower a fresh and consistent appearance. On this occasion, I used a White colour from the Tile Doctor range of Grout Colourant’s, it’s an epoxy based colourant that protects and rejuvenate the grout lines.

I had to use 2 coats of colourant to get the best result and then moved on to putting new silicone around the shower base with a high-quality mould resistant silicone. When finished adding fresh silicone I tidied up again and the job was complete.

Ceramic Tiled Shower Cubicle After Restoration Moston Ceramic Tiled Shower After Restoration Moston

I think you can’t argue the shower cubicle was transformed and customer even said it looks better then when it was new; we also fixed few chips for her whilst there and stripped and replaced the silicone around the sink as a bonus.

Ceramic Tiled Sink Grout Before Cleaning Moston Ceramic Tiled Sink After Cleaning Moston

 
 
Source: Ceramic Tile and Grout Cleaning Service in Machester

Treating Mouldy Grout in a Shower Cubicle in Cumbria

Grange-over-Sands is a quaint little town on the Morecambe bay, roughly halfway between Barrow-in-Furness and Kendal in Cumbria. I was recently contacted by a property owner in the area who had heard about Tile Doctor services and was keen to have us restore their tiled shower cubicle which, as you can see from the photos below, had staining and mould on the ceramic tile, grout and silicone sealant.

Shower Cubicle in Grange-over-Sands Before Cleaning

The shower cubicle was looking far from inviting and well in need of a good deep clean. I agreed a quote for cleaning and recolouring of the grout, and was soon on my way to the property to carry out the work.

Shower Cubicle in Grange-over-Sands Before Cleaning

Cleaning and Recolouring a White Tiled Shower Cubicle

I started by cleaning the dirty grout with Tile Doctor Mould Away, which is a fast and effective formula for the removal of mould from silicone and grout. I sprayed the product onto the tile and grout and left it to soak in for five minutes, before scrubbing the area with a stiff brush. I then rinsed the area with water, and repeated the process until the mould and staining had completely disappeared.

To guarantee the overall appearance I had agreed with the owner to apply a grout colourant to the grout. For best results, we recommend a pre-treater is applied to the grout first as it helps bond the grout colour to the Grout. The pre-treater was applied then the whole cubicle was rinsed.

The next step was to carefully strip out the old silicone sealant from around the base of the cubicle using a sharp blade.

Colouring Grout in a Shower Cubicle

The grout needs to be dry to take the colourant so after cleaning and pre-treating I dried the grout with a heat gun on a low setting.

Once I was happy the grout was dry I started the recolouring process using a White colourant from the Tile Doctor range which has ten popular colours to choose from including Charcoal Grey, Cappuccino and Black. This would ensure the grout matched nicely with the rest of the cubicle.

The colourant not only restores the colour, it also rejuvenates and seals the grout joints. The lastly step was to apply fresh white silicone around the base of the cubicle.

Shower Cubicle in Grange-over-Sands After Cleaning

I think you will agree from the photos of the finished result the whole cubicle looks much fresher and that it would be difficult to tell the difference from a new installation.

Shower Cubicle in Grange-over-Sands After Cleaning

 
 
Source: Shower Tile and Grout Cleaning Service in South Cumbria

Refreshing the look of Travertine Tile and Grout in a Shower Cubicle

This is a follow-up post from last week where I detailed the restoration of a beautiful polished travertine floor that had been installed on most of the ground floor and bathroom at a property in Newton Heath. After cleaning, polishing and sealing the floor tiles the owners asked if I could apply the same treatment to their Travertine tiled shower cubicle which was not looking its best and had become stained over time.

Travertine Shower Before Cleaning Newton Heath

Cleaning Travertine Shower Wall Tiles

First I successfully cleaned the grout with a medium dilution of Tile Doctor Pro-Clean scrubbed into the wall grout with a special stiff grout brush, the tiles were then rinsed with water and the process repeated until I was satisfied with the result.

Travertine Shower Before Cleaning Newton Heath

To clean the Travertine wall tiles I used the same Diamond pad system as I did on floor, starting from 400 grit and moving up to 3000 grit pads lubricated with a little water, the only difference this time was that I used smaller six inch pads fitter to a hand held burnishing machine.

Sealing Travertine Shower Wall Tiles

After I completed all the cleaning and the tiles had dried I proceeded to seal them with Tile Doctor Colour Grow sealer, this is the same sealer that I used on the floor and the excess was polished off with cotton cloths.

The last remaining step was to strip out the silicone sealant strip from around the base of the shower cubicle and replace with new. I used high quality anti mould silicone sealant that left nice lines and fresh look.

Travertine Shower After Cleaning Newton Heath

Needless to say, that customer was very happy with the work carried out on the floor and shower cubicle and recommended me to his neighbour straight away.

Source: Travertine Tile Cleaning and Restoration Service in Manchester

Giving a Cheshire Kitchen a Makeover with Grout Colouring

You often see some fantastic tiled surfaces transformations in lifestyle and home decoration magazines. This customer, who lives in Stockton Heath, had recently seen a feature in which an area of white kitchen tiles had been transformed by changing the white grout to a charcoal coloured grout, giving it a new and particularly striking appearance.

Grout before recolouring at Stockton Heath kitchen Grout before recolouring at Stockton Heath kitchen

Very impressed with the result, she wanted to know if Tile Doctor could do the same for her white kitchen tiles, which covered the majority of the room. I told her that not only could we do it – we could do it even better in the space of a day!

Here’s how we did it.

Cleaning and Recolouring White Kitchen Tiles

Our process for recolouring grout involves an application of a pre-treatment cleaner to ensure a complete refresh of both the grout and tiles. This pre-treatment cleaner removes any dirt and stains, as well as prepares the the grout joints for a superior bond with the Grout Colourant. I applied this carefully and scrubbed it in using a specialised grout brush, before drying the area with a heat gun.

It was then time to apply Charcoal Gray Grout Colourant, one of the options from our range of 10 Grout Colourants that includes Black, Ivory, and Cappuccino. Our Grout Colourant is an easy-to-use waterborne epoxy that not only recolours grout joints, but also seals and rejuvenates them to guarantee their long-term protection. This was applied using a good old fashioned toothbrush, and any excess was swiftly removed.

Grout during recolouring at Stockton Heath kitchen Grout during recolouring at Stockton Heath kitchen

To complete the process I removed the old silicone around the windows and worktops and replaced with a fresh batch. When the customer saw the finished result she was over the moon. She thought this kind of transformation could only be made with difficulty and at a high cost but we showed that it’s a very simple and cost-effective process for any home owner.

Grout after recolouring at Stockton Heath kitchen Grout after recolouring at Stockton Heath kitchen

 
 
Source: Grout Cleaning and Colouring Service in Cheshire

Removing Grout Smears From Terracotta Tiles

This newly installed Herringbone-style Terracotta tiled floor in a refurbished kitchen was heavily covered with patches of grout haze. The customer, who lives in the town of Cogenhoe, Northampton informed me that the tiler had supposedly sealed the floor before grouting. If this was true, the grout haze should have been very easy to remove.

However, the tiler had clearly not been entirely truthful as, when I arrived at the property to carry out a test clean, I found very little evidence of any sealer whatsoever. Nonetheless, I found that the grout haze was easily removed using a solution of Tile Doctor Grout Clean Up, a concentrated phosphoric acid cleaner which is designed specifically for the removal of haze, mineral deposits and efflorescence.

Herringbone design terracotta floor before Cogenhoe Herringbone design terracotta floor before Cogenhoe

These Terracotta tiles were very pitted and the original tiler was correct to fill the small holes with grout to complement the rustic look of the tiles, but he should have taken the correct measures to ensure that a white misty grout haze didn’t appear over the whole area!

The customer was happy for me to proceed with restoring the floor, but also very concerned that her newly installed hand painted kitchen units would be damaged by the chemical cleaning products. I assured her that I would cover them up completely and carry out all work along the plinths by hand.

Removing Grout Haze from Terracotta Tiles

Once on site, I covered the kitchen units to protect them and proceeded to mix up a solution of Grout Clean Up. This was applied firstly around the edges of the floor and scrubbed into the stone by hand using a stiff brush.

Working in areas of four square metres each so as to not the leave the product on the floor too long, I applied the solution to pre-wet the floor ready for the next part of the process. This was to apply Tile Doctor Acid Gel, our blend of phosphoric and hydrochloric acids, leave it to dwell for a few minutes has then agitate it to neutralise and remove the copious grout haze. Once each area had been treated I rinsed it with water to remove any chemicals.

Herringbone design terracotta floor during Cogenhoe Herringbone design terracotta floor during Cogenhoe

Sealing Terracotta Tiles

With the entire floor treated, I installed a dehumidifier to help the tiles to dry quickly overnight. The next day I returned to the property to apply two coats of Tile Doctor Colour Grow sealer. This is an impregnating sealer which provides robust protection while also lifting the natural shades in the Terracotta.

Each coat was polished in by hand, leaving an hour for drying between coats. I then waited another hour before giving the whole floor a final polish with a buffing machine to remove any excess sealant.

Herringbone design terracotta floor after Cogenhoe Herringbone design terracotta floor after Cogenhoe

The result achieved in the space of 24 hours was fantastic and the customer was exceptionally pleased. Despite the severity of the grout haze problem, the combination of the right products allowed me to handily resolve it. The addition of a properly applied and top quality sealer will help to ensure the floor is protected from staining, something which is essential in a kitchen.
 
 
Source: Tile and Grout Cleaning Service in Northamptonshire

Shower Cubicle Grout Cleaned and Recoloured in Cheshire

It’s not unusual for Shower tile and grout to become stained due to the dyes that are found in soap, mould can also be a common problem but usually this is down to inadequate ventilation. Whilst we do sell products that can keep your tile and grout clean we are also able to assist when a really deep clean is required. The photographs below are a great example of this and are of one of three shower cubicles we were asked to clean and restore at a modernised Victorian property in Sale, Cheshire.

Shower cubicle before cleaning in sale Cheshire Shower cubicle before cleaning in sale Cheshire

Cleaning Ceramic Tile and Grout

We started by spraying the tile and grout down with Tile Doctor Pro-Clean which is a strong alkaline cleaner, spraying it on mixes it air which helps it to stick to Vertical surfaces allowing it to get to work on the dirt. We left it to dwell for ten minutes before scrubbing it in by hand using a stiff grout brush; this process certainly improved the grout but unfortunately it had become too badly stained to be satisfactory so we decided to recolour the grout using a white grout colourant.

To get the wall tiles and shower glass clean we sprayed on Tile Doctor Oxy-Pro, again leaving it to dwell for a while before gently scrubbing it away with water. Once dry we set about stripping off the silicone strip around the base of the shower wall which was stained and impossible to get clean again.

Recolouring Grout

The grout colourant comes in a tube and is very straightforward to apply although I must admit the work is quite tedious. Two coats of white colourant were required to get the uniform appearance needed and I think you will agree the effect is quite transforming. The other advantage of these particular colourant products is that they are epoxy based and form a barrier of the grout preventing future staining and making it very easy to clean going forward.

The last step was to apply new silicone along the base of the cubicle and give the tiles a quick buff.

Shower cubicle after cleaning in sale Cheshire Shower cubicle after cleaning in sale Cheshire

I think you will agree it was quite a transformation and the cubicle now looks like it was recently installed.
 
 
Source: Tile and Grout Cleaning Service in West Cheshire

Rejuvenating Bathroom Tile Grout

Here’s a quick example of an interesting tiled shower cubicle at a property in Edinburgh that was well overdue for a refresh, including deep cleaning and recolouring do the grout lines that had become stained and mouldy. This is a problem that the majority of property owners experience due to the simple fact that shower cubicles come into contact with damaging acid-based shampoos and soaps on a daily basis.

The short-term solution for this is to wash the shower cubicle down with water after each use, however busy people do not always remember to do so! The prognosis is bad discolouration, mould growth and staining if the problem if proper care isn’t taken. In this case, the problem had worsened to the point that the property owner decided to contact Tile a Doctor to provide a thorough refresh of the tiles.

Edinburgh bathroom before grout refresh Edinburgh bathroom before grout refresh

Cleaning Stained and Discoloured Shower Cubicle Tiles

Our process for refreshing shower cubicles in a similar state to this one is simple, but highly effective. I started by mixing a strong solution of our high alkaline cleaner, known as Tile Doctor Pro Clean (diluted to an appropriate level with water), before applying it directly to the tile and grout.

Next, I worked it in using specialised handheld grout brushes , with the alkaline in the Pro Clean neutralising the acidic staining and mould growth had leaving the area clean and fresh. Pro Clean is suitable for use on all kinds of natural stone, and on both verticals and horizontal surfaces. Once satisfied the grout had been cleaned to the best of my abilities, I quickly dried the entire area using a heat gun.

Recolouring Shower Cubicle Grout

To restore the appearance of the installation back to it’s optimal appearance I chose to recolour the grout lines with our Light Grey grout colourant, which matched in very nicely. This is just one of ten different colours of grout colourant we offer. The colourant was left to dry for a short period before I cleaned off any excess. The final stage of the refresh involved stripping off the old discoloured silicone from around the bath and replacing it with fresh silicone.

Edinburgh bathroom before grout refresh Edinburgh bathroom before grout refresh

The customer was very impressed by the speed and efficiency of the refresh. With the work completed to a high standard in just a few hours, she now has one less problem to worry about – and a very smart looking shower cubicle! Another satisfied customer.
 
 
Source: Tile and Grout Cleaning and Renovation Service in Edinburgh

Refreshing the Appearance of Bathroom Grout

We commonly encounter customers who are struggling to keep their Ceramic tiled shower cubicles clean. Since most people use their showers every day, the tiles and grout inevitably come into contact with shampoos and soaps that can cause staining, discolouration and mould. In fact, it’s not uncommon for property owners to completely give up on trying to clean the tiles, especially as many everyday cleaners are ineffectual, and this allows the situation to worsen over time.

This customer, who lives in Hale Village – known to be one of the UK’s quietest and best kept villages despite being just outside the busy city of Liverpool – was fed up with the state of her tiled shower cubicle and decided to seek professional assistance. I explained that with regular maintenance using suitable products, the tiles could be easily kept clean. I visited the property to show her first hand the results that could be achieved by cleaning and recolouring the grout.

Ceramic bath tiles before refresh Hale Village Ceramic bath tiles before refresh Hale Village

Grout Cleaning and Recolouring Ceramic Bathroom Tiles

The ideal product for cleaning grout that has become affected by mould is Tile Doctor Mould Away, a fast and effective formula that can be directly applied. After applying the Mould Away I allowed it to soak into the grout for 20 minutes, before scrubbing it in with a special handheld brush. I also scrubbed it into the tiles to remove any excess staining caused by coming into contact with shampoos and soaps.

After completing a thorough clean of both the grout and tiles, it was time to remove the old silicone sealant from around the edges of the bath, and replace it with a fresh white sealant. I then opted to recolour the grout to match it with the tiles and the new sealant, doing so carefully with Tile Doctor’s own White Grout Colourant. This is just one of ten different Grout Colourant options we offer. Other options include Charcoal Grey, Black and Cappuccino Brown to much different colour tiles.

Ceramic bath tiles after refresh Hale Village Ceramic bath tiles after refresh Hale Village

The combination of cleaning and recolouring completely refreshed the appearance of this Ceramic tiled shower cubicle, to the point that it almost looks new. Needless to say my customer was very happy, and can see now just how easy it can be to keep these tiles looking good using the right products.
 
 
Source: Bathroom Tile and Grout Cleaning Service in Cheshire

New but Discoloured Grout refreshed in a Warrington Kitchen

It can be amazing and equally frustrating just how quickly grout can become dirty and discoloured. I was recently contacted by a couple in Warrington to see if I could help them with their Ceramic tiled kitchen floor that had only been laid six months earlier. To their dismay, in that short time the grout had become discoloured and difficult to clean. They had given up trying to resolve the situation by themselves and so turned to Tile Doctor for some professional assistance.

Naturally I was happy to assist and so arranged to visit the property to conduct a small cleaning test where I demonstrated how with a combination of the right tools and products I could indeed get the grout lines clean again. Seeing the results of the test, the couple were more than happy to book me to complete the job.

Kitchen tiles before cleaning and grout recolour in Warrington

Grout Cleaning for Dirty Ceramic Tiles

On my return to the property, I repeated the same successful test clean across the entirety of the floor. This involved the application firstly of Tile Doctor Remove and Go, which is a strong cleaner, stripper and degreaser. I scrubbed the product thoroughly into all the grout lines, making sure I did not miss any dirt and stains.

I then started to clean the Ceramic floor tiles using our high alkaline cleaner, Tile Doctor Pro Clean. This was scrubbed into the floor in a similar fashion to the Remove and Go and then rinsed off with plain water extracting the waste water with a Wet Vat. The floor was left to dry over lunchtime.

Recolouring Grout for Ceramic Tiles

In the afternoon, I explained that whilst I could get the grout clean it was only a matter of time before it became dirty again. So, to provide a permanent solution I recommended to the customer that we apply an epoxy Grout Colourant, which adds a protective barrier over the grout. An alternative would have been to apply a Grout Sealer however this is best applied to new grout and in this case would not have guaranteed the uniform appearance required.

Before applying the Grout Colourant, I made sure the grout lines were dry by giving them a quick blast with a heat gun. I then started to colour the grout lines with our White Grout Colourant, which is part of a range made by Tile Doctor and is available in ten popular colours, including Black, Charcoal Grey and even Cappuccino Brown.

The difference made to the floor was quite remarkable. Not only is the grout now a uniform brilliant white, but it should remain so for a long time to come. You can see this yourself in the photograph below!

Kitchen tiles after cleaning and grout recolour in Warrington

 
 
Source: Tile and Grout Cleaning and Restoration Service in West Cheshire

Restoring the Appearance of Grout on a Tiled Kitchen Worktop

Tiled kitchen worktops work really well, but just like any other kind of tiled surface they will need regular cleaning and maintenance to keep them looking great. Kitchen worktops in particular can fall into poor condition quickly when exposed to all manner of dirt and stains resulting from food preparation, with the grout lines often suffering the most which if you have tiles in your shower is a problem I’m sure you will be familiar with.

Mosaic tiled worktop before grout colouring

The grout lines on this Mosaic tiled kitchen worktop had become discoloured following years of exposure to soaps and washing up liquid from the nearby sink, as well as, most likely, food and drink spillages. The property was in the picturesque village of Silverdale, Morecambe Bay, and the owner had decided it was time to have the worktop professionally refreshed. This was a job that would only take a few hours to complete, and would involve both grout cleaning and recolouring.

Mosaic tiled worktop before grout colouring

Cleaning and Recolouring Dirty Grout for a Mosaic Worktop

Before beginning the restoration, I had to decide upon the best method. I realised that if I took out the grout to replace it completely I may have dislodged or even damaged the tiles – especially considering that they are at least 30 years old and give the age of the tiles it would be difficult if not impossible to find replacements if they were damaged.

As a result, I opted to clean the tiles and grout using Tile Doctor Oxy Gel. This product is a strong alkaline-based cleaner in gel form designed to break down dirt and grime, including soap scum and mildew stains. While it can be used on both horizontal and vertical surfaces, it is particularly suitable for the latter as the gel is able to dwell for a long time without running down the wall. Oxy Gel proved to be very effective in restoring the grout lines to top form, but I chose to follow by steam cleaning the area to get rid of any bacteria.

Mosaic tiled worktop during grout colouring

To finish the restoration, I recoloured the grout lines using our fresh White grout colourant – one of 10 available colours. Tile Doctor’s grout colourant seals and rejuvenates existing grout joints, and is equally effective for interior or exterior applications, including bathrooms and kitchens. The colourant was left for a little while to cure, before I polished off the excess with white sponge pads.

Mosaic tiled worktop after grout colouring

The result was a quick and effective transformation for the Mosaic tiled kitchen worktop that left the customer very happy!
 
 
Source: Worktop Tile and Grout Maintenance Service in Lancashire

Dealing with Mould on Grout

A common problem with bathroom and shower cubicle tiles is the appearance of mould on the tile, grout and silicone which if not tackled on a regular basis will spread and threaten to severely damage the appearance of the tiles, along with the silicone. This problem is usually due to inadequate ventilation however the good news is that with early intervention with Tile Doctor Mould Away spray the problem can be reversed.

The two photos below show a bad case of this very problem at a property in Northampton, where you can see that the grout and silicone sealant had become black with mould.

Mouldy shower cubicle before Northampton Mouldy shower cubicle before Northampton

Cleaning and Repairing Damaged Shower Cubicle Grout

Firstly, I decided to cut out the damaged grout with a hand held disc cutter and remove all the silicone at the base of the shower. To treat the less invasive mould in the rest of the cubicle I sprayed it with Tile Doctor Mould Away, which is specifically designed to remove mould from silicone and grout.

I sprayed the product onto the affected areas and left it to dwell for five minutes, before scrubbing it in with a stiff grout brush, resulting in a good clean. The area was then rinsed with plain water. Finally, I replaced the grout and the silicone that I had removed earlier with a flexible grout and a white silicone, both of which include a mould inhibitor.

Mouldy shower cubicle after Northampton Mouldy shower cubicle after Northampton

The photographs above show the end result. The customer was very happy with her refreshed tiles, and left the following feedback:

“Phil was brilliant – both when he came to look at the job and then when he returned to actually make the grout repairs. Most importantly he explained what was (and wasn’t possible) and did exactly what he said he would do. My shower area now looks brilliant and I’m no longer showering in fear of the tiles falling off the wall! Honest, clean, timely and totally professional. A tremendous job well done. Thank you.”

I left the customer with a bottle of Tile Doctor Aqua Pro to aid with regular cleaning. If used once or twice a week, this product will help maintain the condition of the grout. I also advised the customer that it is good practice to rinse the tiles down with plain water using the shower head after each shower to remove any soapy residue which can slowly discolour and stain grout over time.
 
 
Source: Shower Tile and Grout Maintenance Service in Northamptonshire

Removing Varnish From Grout in Harrogate

I was recently at a property in the North Yorkshire town of Harrogate, undertaking what I initially thought would be the cleaning and polishing of a Cream Limestone tiled kitchen. However, as I began the cleaning process I quickly discovered that under the dirty grout lines someone had taken a lot of effort to paint with a small brush directly onto the grout using varnish!

Cream limestone floor before cleaning Harrogate Cream limestone floor before cleaning Harrogate

Removing Varnish from Grout

In a normal situation, I would have covered the whole floor with Tile Doctor Remove & Go to solve the problem, however compared to, say, adhesive or paint staining, varnish is very difficult to remove. So instead I opted for the long, yet necessary process of cleaning the grout manually with several thin wire brushes. Over the course of two days I managed to remove approximately 90% of the stubborn varnish – and could finally move onto cleaning and polishing the Limestone as originally planned.

Burnishing and Sealing a Limestone Tiled Kitchen Floor

The polish had been lost from the Limestone kitchen tiles over time, so I set about restoring it using a type of polishing known as burnishing. This involves the application of diamond encrusted pads of varying grit to the floor to gradually buff the stone and achieve an aesthetic and durable shine. Burnishing is most commonly used on high-end stone such as Marble, Travertine and, of course, Limestone.

At Tile Doctor, our burnishing system comprises four burnishing pads, ranging from a Coarse grit to a Very Fine grit. After applying the first three pads (Coarse, Medium and Fine), I gave the tiles a further clean with Tile a Doctor Pro Clean, which is our alkaline cleaner, to remove any residue from the burnishing process. I then rinsed the floor with clean water and soaked up the residue with a wet vacuum, before leaving it to dry.

The floor was then polished to a satin finish using the fourth and final Extra Fine burnishing pad. I sealed it using a couple of coats of Tile Doctor Ultra-Seal, an impregnating sealer designed to provide maximum protection against dirt and stains.

Cream limestone floor after cleaning Harrogate Cream limestone floor after cleaning Harrogate

The combination of burnishing and sealing always makes a huge difference to Limestone tiles. Here, the finished result was almost like a new floor! The customer was both amazed and very pleased with the transformation.
 
 
Source: Limestone Tile and Grout Cleaning and Maintenance Service in North Yorkshire

Grout Damaged with Acid Restored with Grout Colourant in Cheshire

It’s always a good idea to double-check any tile cleaning advice you receive with a professional. Sometimes advice can be inaccurate and cause more problems than good. Such was the case with this customer, who lives in the small town of Appleton near Warrington. He had been advised by his builder to use brick acid to remove carpet glue from a newly discovered Quarry tiled floor. Taking the advice, he had washed the floor several times with a solution of brick acid diluted with water. But while this seemed to successfully remove the carpet glue, it also severely discoloured the grout lines, leaving the entire floor looking grubby and unappealing.

The customer was just about to go on holiday, and asked me to see what could be done to restore the floor’s appearance while he was gone. With the house to myself, I got to work.

Quarry Tiles Before Cleaning in Appleton

Cleaning a Stained Quarry Tiled Floor

My first job was to strip the floor property to remove old sealers present on the tile using a strong dilution of our high alkaline cleaner, Tile Doctor Pro Clean. We use this cleaner on all types of tile and natural stone due to its versatility and consistency.

I spread the solution onto the floor and left to dwell for twenty minutes before scrubbing with a black pad fitted to a floor rotary machine. This process also removed the years of dirt and dust that had penetrated through the recently removed carpet. I also paid attention to the grout lines giving them a good scrub with a stiff grout brush, but the acid staining proved to be impossible to remove completely.

While I’m not sure exactly how long the floor had been covered by carpet, it’s safe to say a deep clean had been long, long overdue. Once I had cleaned the floor to a high standard, I used a wet-vac to remove the now dirty cleaning solution from the floor, before leaving it to dry off completely overnight.

Sealing a Quarry Tiled Floor

Upon my return to the property the next day, I tested to make sure the floor was dry enough to seal, which is important as excess moisture can cloud the sealer and damage its performance.

Once satisfied, I applied one coat of Tile Doctor Colour Grow, which is our impregnating sealer designed to really bring out the natural colours in the tile, followed by two coats of Tile Doctor Seal and Go to give the tiles a stain resistant, low-sheen finish.

After this was dry I coloured the grout lines with a matching Tile Doctor Grout Colourant to cover and hide the damage the acid had caused to the grout lines. Finally, I gave the floor three more coats of Seal and Go to add the finishing touches.

Quarry Tiles After Cleaning in Appleton

My customer returned from holiday to find a completely transformed floor. Looking at the before and after photos, it is easy to see why he was more than happy with the result! Another satisfied customer.
 
 
Source: Tile and Grout Restoration Service in Cheshire

Dealing With Discoloured Shower Cubicle Grout

Shower cubicles can be the most difficult of tiled features to keep clean. Most are exposed to various acid-based soaps and shampoos on a daily basis, allowing mould and general muck to quickly build up along the grout lines and silicone. This leaves the entire area looking quite unappealing. In some cases, the grout lines become stained beyond a point where they can be restored to their original condition, so property owners will typically request to have the grout cut out and replaced however a faster and cheaper method is to have the grout completely recoloured.

Such was the case with this Ceramic tiled shower cubicle at a house in Wigan. It would take a lot to get the cubicle looking great again, having not been cleaned properly for a long time. The property owner decided to contact me for a professional refresh, including cleaning, new silicone sealer and recolouring of the grout.

Ceramic Shower Cubicle Before Refresh Wigan

Cleaning a Ceramic Tiles Shower Cubicle

I started the refresh by applying Tile Doctor Mould Away spray to the tiles and grout, and leaving it to dwell for an hour. As the name of the product suggests, Mould Away is a fast and effective cleaner for the removal of mould from silicone and grout, making it ideal for use on shower cubicles similar to this one. I then rinsed the entire area down with water before scrubbing the grout lines and tiles with a stiff grout brush to remove any remaining mould and lime scale, leaving them looking a lot cleaner.

Colouring Grout in a Ceramic Tiles Shower Cubicle

The cleaning process made a big improvement however the grout was still too stained so after removing the silicone strip from around the base of the shower I proceeded to recolour with our white Grout Colourant. The colourant is painted onto the grout and any excess is wiped of the tile before it dries which both improves the appearance of the grout and seals it in to protect it from further staining. The last step was to apply fresh white silicone along the base of the shower.

Ceramic Shower Cubicle After Refresh Wigan

The customer was very pleased with the refreshed appearance of their shower and you must admit it looks much more inviting now.
 
 
Source: Ceramic Tile Clearing and Restoration Service in Greater Manchester

Achieving the Consistent Appearance of old Grout using Grout Colourant

The task of keeping these white Ceramic Kitchen and Conservatory tiles clean was proving very challenging for this customer, who lives in the town of Somerton in Somerset. Somerton is known for its bustling market, which has supposedly been run on a weekly basis since the Middle Ages, and its famous ‘Market Cross’ at the centre of the beautiful marketplace is a popular tourist attraction for visitors to the West Country.

It probably comes as no surprise to anyone that white tiles are often more difficult to keep clean than others. However, in this case, rather than being badly marked or damaged, these Ceramic tiles had become dirty due to the surface being pitted rather than smooth which trapped ground in marks from spills and dirty footprints etc. The pitted rough surface is very characteristic and provides better grip however they do trap dirt are therefore more difficult to keep clean.

The grout had also suffered over the years, losing a lot of its colour in the process so as well as cleaning the tiles we agreed to give the grout a really deep clean and also to colour the grout to make it more uniform.

Cleaning a Pitted Ceramic Tiled Floor

To clean the tiles, I firstly created a strong diluted of Tile Doctor Pro Clean and applied it liberally across the entire floor, leaving it to dwell and soak into the tile for a short period in order to soften the ingrained dirt. I then used my heavy weight rotary machine fitted with a black scrubbing pad to agitate the solution and break down the muck.

Once satisfied with the condition of the tiles I turned my attention to the grout lines, cleaning them carefully by hand using a stiff tile cleaning brush and the same solution of Pro Clean and water. This provided a deep, penetrating that clean that left the grout lines clean and free from the dirt and grease that had dulled their appearance for so long.

With some great results achieved through the cleaning, I rinsed the whole floor to wash away any leftover Pro-Clean and left it to dry fully overnight.

Ceramic Tiles Somerton After Cleaning but Before Grout Colouring

Recolouring Grout for a Ceramic Tiled Floor

I returned to the property the next day to check on the floor and after ensuring the floor was completely dry, proceeded to recolour the grout lines using Tile Doctor’s Grout Colourant. Our Grout Colourants are a waterborne epoxy that recolours, seals and rejuvenates existing grout joints and is available in ten different colours ranging from white to dark greys. The scrubbing with Pro-Clean the day before would also ensure the surface of the grout was clean and would make a good surface for the colourant to bond with.

Since in the past the grout lines had undergone a number of repairs, the existing colour was a mix of different greys. It made most sense then that they picked our ‘Natural Grey’ Grout Colourant for me to use. I painted the Colourant on carefully and waited for 30 minutes before removing any excess, leaving the grout lines perfectly covered in a uniform colour.

Ceramic Tiles Somerton After Cleaning and Grout Colouring

The difference was really noticeable and the property owner was really happy with the results. As you can see from the photos, the new grey Colourant really made the grout lines stand out against the clean white Ceramic tiles. Another satisfied customer.
 
 
Source: Grout Cleaning and Colouring Service in Somerset

Restoring the Appearance of Grout in Preston with a Colourant

Well maintained grout is fundamental to achieving a great looking tiled floor, whatever your choice of tile or stone. Even if the tiles themselves are in reasonably good condition, dirty and damaged grout lines can really upset the overall appearance of the floor.

Such was the case with this Ceramic Terracotta tiled floor in the bustling Lancashire town of Preston. The property owner recently had a new kitchen installed, but chose not to have new tiles fitted since the original tiles (dating back a good 15 years) were still in fantastic physical condition, with no chips or breaks. This is quite surprising considering that the kitchen is typically one of the main areas of traffic in any house however Ceramic and Porcelain tiles are very durable.

The grout, however, told a different story: it was very dirty and even missing in parts. Over the years it had come away and was replaced with new grout, however, this had left the whole floor with a displeasing patchy finish. Upon closer inspection it also became clear that the tiles themselves could do with a deep clean. I stepped in to discuss what could be done to improve the appearance of the floor and recommended a deep clean and grout colouring.

Grout Colouring Preston Before

Cleaning Ceramic Terracotta Tiles and Grout

Tile Doctor Pro Clean, a versatile high alkaline cleaner, was my choice of product for removing the dirt from the tiles. I applied it liberally across the floor before scrubbing it in with a scrubbing pad fitted to a rotary machine. Pro Clean is a go-to product for the removal of dirt, stains and other muck on most kinds of natural stone floor, and is capable of dealing with small amounts of soil to heavy buildup.

Once the tiles had been cleaned I turned special attention to the grout. I cleaned it with a product called Grout Colourant Pre-Treatment Cleaner, which is slightly acidic to break down ingrained dirt and tackle inherent grout smears, while ensuring that grout colourant bonds to the grout once it is applied.

Colouring Grout for Ceramic Terracotta a Tiles

The job took two days to complete as it was quite a large floor stretching into several rooms. The floor also needed to dry off overnight once I had completed the cleaning process, so I decided to call back the next day once it had dried completely. Upon my return I proceeded to colour the freshly cleaned grout by applying one coat of natural grey colourant. Sometimes two coats might be required for blending purposes, but not on this occasion.

The customer was very happy with the results. She had, in fact, thought of ripping up the old tiles as part of the kitchen restoration, but she decided not to since she really likes the tiles. A restoration by the Lancashire Tile Doctor was the appropriate and much less expensive choice!

Grout Colouring Preston After

 
 
Source: Ceramic Tile and Grout Cleaning Service in Lancashire

Completly changing the Appearance of Ceramic Tile and Grout in Flintshire

Moving into a new home is a stressful but rewarding experience. This customer had just recently moved into a property in the neighbouring and historic Flintshire town of Mold, and was keen to make some renovations.

High on the agenda was the restoration of a large number of Ceramic floor tiles spread throughout multiple downstairs rooms. Although undecided as to whether to keep the tiles for the long-term or have them removed, the customer did resolve to have them professionally cleaned, especially since the previous owner had left the grout in a miserable state.

Ceramic Tiled Floor Before Cleaning in Mould

Upon initial inspection I noticed that the previous owner had attempted to put more grout on top of the existing one in some areas, the problem with this being that the two groups were of different colours. This left the grout looking inconsistent and dirtier than it actually was. I mentioned to the customer that I could re-colour the grout for them after cleaning the floor and that it would be the best solution in this situation.

Ceramic Tiled Floor Before Cleaning in Mould

Cleaning and Colouring Ceramic Tiled Floor Grout

As mentioned, the tiles themselves needed a deep clean, and so I set about applying a strong dilution of Tile Doctor Pro Clean liberally over the floor and leaving it to dwell for a short period. This allows the product, a high alkaline cleaner suitable for use on most natural stone floors, to seep into the pores of the stone to lift out and dissolve ingrained dirt and stains. Once I had allowed it to dwell I scrubbed the product into the tiles using a black pad fitted to a rotary machine.

Of course I also paid special attention to the grout lines, carefully cleaning them using more Pro Clean. With some floors I usually give the floor an acid wash at this with Tile Doctor Grout Clean Up to remove grout smears and mineral salt deposits but this was not necessary on this particular occasion.

Ceramic Tiled Floor After Cleaning in Mould

Once I had cleaned the entire floor I gave it a thorough rinse with water which was then extracted using a wet vacuum before leaving the floor to dry for two hours assisted with an air mover to speed up the process. When happy that the tiles were completely dry and ready to be re-coloured I went ahead and carefully applied a new black Grout Colourant that matched very well with the natural colour of the stone, giving the whole floor a smarter appearance.

Ceramic Tiled Floor After Cleaning in Mould

The customer was really pleased with the result and left some nice feedback on the job as a whole:

“Excellent experience all round, from initial consultation through to colour advice and scheduling work. Cannot speak highly enough of Joe, thoroughly professional and an amazing result. Highly recommended.”
 
 
Source: Ceramic Tile and Stone Restoration Service in Shropshire

Kitchen Tile Grout Refresh

If you’re looking to give your kitchen a face lift then read on as the following post details a very simple grout treatment that I think you will agree really refreshed the look of this kitchen in Edinburgh. In fact if you’re thinking of selling your property this quick but effective grout treatment will really make your tiles look a lot more appealing.

Normally to get grout clean we recommend a good scrub with Tile Doctor Pro-Clean however in some cases the staining cannot be removed completely and sometimes the customer simply wants a different grout colour. In either case whether its wall or floor grout the solution is to re-colour the grout with a Grout Colourant which are available in ten popular colours.

Kitchen Wall Tile Before Refresh in Edinburgh Kitchen Wall Tile Before Refresh in Edinburgh

As you can see in the photographs above the Kitchen Wall Grout for this ceramic tiled kitchen in Edinburgh was a grey colour which looked dirty and was not very attractive.

Cleaning and Colouring Grout

The first step before grout colouring is to give the grout a good scrub with Tile Doctor Pro-Clean to get it as clean as possible before applying the colourant. The grout was then wiped and then allowed to dry ready for the colourant to be applied.

Once the grout was ready the colourant was run evenly along the grout line in thin coats so it didn’t run, working the brush backwards and forwards and taking care to minimise the amount of colourant left on the tile. One coat is usually sufficient but you may need to apply a number of coats if the original grout colour was quite dark.

Kitchen Wall Tile After Refresh in Edinburgh Kitchen Wall Tile After Refresh in Edinburgh

I think you will agree from the photographs the white colourant gave the tiles a really fresh feel and gave the impression the tiling was recent. The colourant also adds a barrier over the grout protecting it from staining and making it easier to clean in future.
 
 
Source: Refreshing Tile and Grout Service

Bathroom Tile Grout Refresh

To clean grout we normally recommend a good scrub with Tile Doctor Pro-Clean which is an strong alkaline product, in some cases however the staining cannot be removed completely and the only thing your can do with the exception of re-grouting is to re-colour the grout with a Grout Colourant which are available in ten popular colours.

In the case of this bathroom at a house in Paisley near Glasgow both the floor of the bathroom and the shower wall tiles were in need of a refresh and after a review of possible solutions is was agreed the easiest thing to do would be to re-colour the floor grout with a Light Grey colourant and the wall tiles with a White colourant.

Bathroom Floor Paisley Before Grout Colouring Shower Wall Tiles Paisley Before Grout Colouring

Cleaning and Colouring Grout

The first step before grout colouring is to give the grout a good scrub with Tile Doctor Pro-Clean to get it as clean as possible before applying the colourant. The grout was then rinsed and then dried ready for the colourant to be applied. You may be surprised to hear but we often find the biggest cause of staining to grout are the dyes contained in soaps and shampoos.

Once the grout is ready it’s a straightforward process of applying the colourant evenly along with thin coats along the grout line working the brush backwards and forwards whilst minimising the amount that gets on the tile. We were not changing the colour of the grout substantially so one coat of colourant was sufficient for both sets of tile.

With two colours being applied we were careful to ensure different brushes were used for each job to avoid any contamination and once the job was complete a damp pad was used to remove excess product from the tile surface.

Bathroom Floor Paisley After Grout Colouring Shower Wall Tiles Paisley After Grout Colouring

As you can see from the photographs the difference was immediate, the other advantage of the colourant is it forms a barrier over the grout protecting it from staining and making it easier to clean going forward.
 
 
Source: Bathroom Tile and Grout Cleaning Service in Paisley

Dealing With Stained Grout

Details below of a Grout colouring job I recently completed at a house in Morecambe. In this instance, the grout had become stained, and my client was no longer happy with it.

There are a number of reasons grout can lose its appearance including the build-up of mould in damp and unvented areas, staining from liquids accidentally spilt on the floor and surprisingly if you have a coloured grout it can lose its colour due to the bleach found in common types of household cleaning products. Grout contains lime which is acid-sensitive and will react to acidic cleaning products so for general cleaning do use a pH Neutral Cleaning product.

Grout Colouring Morecambe 1 Before Grout Colouring Morecambe 2 Before

To tackle the stained grout I first tried Tile Doctor Pro-Clean which can be used at different levels of concentration to increase its potency. In this case however when this grout dried it went back to being patchy so then the only answer was to restore its appearance using a Grout Colouring kit.

Grout Cleaning and Colouring

To form a better bond with the Grout Colourant I first treated the grout with a Tile Doctor Pre-Treat Cleaner, which is very slightly acidic and effectively etches the grout. If you have a particularly acid-sensitive stone tile (Limestone, for example), it is recommended to use Tile Doctor Oxy-Pro cleaner instead as this won’t upset the stone, yet still clean the Grout ready for colouring.

Once the Grout had dried (which is some cases can be several hours), I applied a thin coating of the Grout Colourant, as a thin coat dries quicker and provides a more even finish. A second coat was then added, before polishing off the excess from the edges of the tiles. After about half an hour the Grout Colourant was dry to the touch (at this stage you should be able to walk on the floor). Note that if you are Grout colouring a wall tile in a shower cubicle, it is best to leave the area for 24 hours before using the shower.

Grout Colouring Morecambe 2 After Grout Colouring Morecambe 2 After

As you can see from the photographs, the result was very effective, and needless to say my client was very happy with the rejuvenated appearance of her grout.
 
 
Source: Grout Stain Cleaning service in Lancashire

Grout Haze Removed from Sealed Sandstone Floor

It’s not that uncommon for newly installed tiled floors to suffer from grout haze. This occurs where builder or tiler fails to remove all the excess grout from the surface of the tile after installation. It’s not always immediately obvious as the grout has to dry before it shows up and if the tiles are sealed afterward the grout is trapped on the surface of the tile under the sealer which makes it even more difficult to remove. Not too long ago, I was called to address this exact problem experienced on my client’s Sandstone tiled floor at her house Wappenham, Northamptonshire.

This first picture shows how the builder had left the floor after sealing (note how all the tiles have a similar colour). Also shown in the picture is the equipment I use to remove grout haze should you wish to do this yourself.

Grout Haze Removal from Sandstone Wappenham

The second picture shows a close-up of the white grout haze deposits on the surface of the tile; the issue is probably difficult to appreciate if you haven’t come across this type of problem yourself however you will find ordinary household cleaning products will be largely ineffectual.

Grout Haze Removal from Sandstone Wappenham

Removing Sealer from Sandstone Floor Tiles

The third picture shows the first stage of the cleaning process which required stripping off the sealer so I could then treat the Grout Haze. To do this I applied Tile Doctor Remove & Go liberally across the floor, before agitating with a black stripping pad fitted to a rotary machine to break down the old surface sealer. I followed this by using a wet-vac machine to remove any soiled residue. As you can see in the next photograph, the colours are already starting to show.

Grout Haze Removal from Sandstone Wappenham

Treating Grout Haze on Sandstone

The next photo shows the second stage of the process, which involved the application of a new product in the Tile Doctor range called Acid Gel. The acid based formula is required to remove the cement/grout and being a gel you find the product remains in situ breaking down the grout haze instead of spreading around as you would expect with a liquid.

Grout Haze Removal from Sandstone Wappenham

I left the Acid Gel to dwell for approximately ten minutes, before mixing it with water and scrubbing it into the tiles with an industrial brush. This was followed by a second wet vacuum to ensure all the residue was removed. A turbo dryer was used on the treated area to speed up the drying process whilst I moved onto the next section.

Grout Haze Removal from Sandstone Wappenham Grout Haze Removal from Sandstone Wappenham

Sealing Sandstone Floor Tiles

Once the floor was fully dry I was able to seal it again with a couple of coats of Tile Doctor Colour Grow. Sealing will protect the floor from staining and make it easier to clean, additionally Colour Grow soaks into the pores of the stone protecting it from within and enhancing the natural colours of the stone in the process.

Grout Haze Removal from Sandstone Wappenham

The final photograph shows an area which has been fully sealed and the tiles restored to their natural beauty. I achieved this result across the entirety of the floor.
 
 
Source: Sandstone Floor Cleaning and Restoration service in Northamptonshire

Applying Charcoal Grey Grout Colourant

Here’s a quick grout cleaning and re-colouring job I completed in the town of Canvey Island, Essex. Canvey Island lies on the south east coast, and lies just above sea level which in my job is always worth noting as the area can be prone to flooding. This wasn’t the problem here though, simply put, my client was unhappy with the colour of their grout, and wanted it re-coloured to a darker shade to match the grey Ceramic floor tiles.

Cleaning the grout before re-colouring is essential because, as many readers are probably well aware, grouts are porous and therefore can very easily absorb dirt and grease. Most often this will result in grout discolouration if not dealt with promptly.

Ceramic tiles before cleaning and colouring in canvey island

Cleaning and Re-Colouring the grout lines of a Ceramic tiled floor

So, as mentioned above the first step in the re-colouring process involved cleaning the grout lines. For this Tile Doctor has a special Pre-Treat Cleaner which is sprayed on and scrubbed into the grout to both remove any existing dirt and also to prepare the grout joints for a superior bond with the Grout Colourant. Once complete the grout lines looked clean and refreshed.

To clean the ceramic I diluted one part Tile Doctor Pro-Clean to three parts water, and used it to wash down the Ceramic tiles, leaving a consistent level of cleanliness across the entire floor. I then rinsed the floor with water which was then extracted using a wet vacuum and waited for 3 hours for the floor to dry.

Once dry, I began the process of applying the Charcoal Grey (as chosen by the client) Grout Colourant to the grout lines. As well as changing the colour the colourant also forms a barrier over the grout sealing it in and protecting it from future staining for years to come.

Then, once dry, the floor was given another quick clean using a light spray of water and a white buffing pad, resulting in an aesthetically pleasing sheen finish. My client was very happy with the outcome and now has the floor they wanted.

Ceramic tiles after cleaning and colouring in canvey island

 
 
Source: Tile, Stone, Grout Cleaning and Colouring service in South-Essex

Dealing With Blackened Grout on Travertine Kitchen Tiles

Earlier this month I was in the town of Northampton, to see a client who had reported a problem with her Travertine kitchen tiles. Basically the grout between the tiles was badly stained, to the point of appearing almost black.

Travertine Tiled Kitchen with Stained Grout Northampton

The Travertine tiles were also in need of some maintenance, and so I was commissioned to provide a clean, polish and a fresh seal. Travertine is a popular choice for kitchen flooring due to its relatively high durability and distinct features. My task was to get this floor back to looking its best.

Cleaning badly stained grout

My priority was to address the badly stained grout so I cleaned the grout lines by hand using a combination of hand brushes and Tile Doctor Grout Clean-Up. The surface was pre-wet with water, before a solution of Grout-Clean Up and clean water was applied to the surface. The brushes were then used to agitate the solution. Grout Clean-Up contains a mix of concentrated phosphoric acid and cleaner designed to penetrate below the surface of the grout to remove grout stains, smears and mineral deposits.

As you can see from the photos, Grout Clean-Up made an immediate difference to the appearance of the tiles. This product is suitable for use on masonry and acid resistant surfaces. After completing the clean, I gave the floor a thorough rinse to neutralise the floor after cleaning and removed as much of the water as possible using a wet vacuum.

Travertine Tiled Kitchen with Stained Grout Northampton

Burnishing Travertine tiles

Following this, I paid attention to the tiles themselves, cleaning them to achieve a polished effect by using a system of burnishing pads. Tile Doctor burnishing pads comprise a set of four pads varying in grit type, from Coarse and Medium to Fine and Very Fine. I applied all four pads in turn to the floor, stopping to rinse the floor in between each. The result was a high quality polished finish.

I then left the floor to dry completely overnight, before commencing the seal the next day. My choice of sealing product was Tile Doctor Colour Grow which is a colour intensifying sealer that both enhances the natural appearance of the stone and provides a durable surface seal.

Travertine Tiled Kitchen with Stained Grout Northampton

My client was very pleased with the finished product, and left the following comment on the Tile Doctor feedback system: “efficiently done”, yielding “good results”.
 
 
Source: Travertine Tile and Grout cleaning and sealing service in Northamptonshire

Shower Cubicle Grout Refresh

The photographs below were taken at a private residence in the town of Stafford, the owner of the house was unhappy with the state of the grout lines in their ceramic tiled shower which had, over time, had become grey and stained. As you cans see from the photograph, the whole area in general was very tired looking. I recommended a grout clean, colouring and seal to get the shower back to looking its best. My client was happy with me to proceed and I promptly began the work.

Grout Colouring Ceramic shower tiled cubicle in stafford before

Grout Colouring including Prep

My first task was to clean the grout using a grout colouring pre-treater which cleans and prepares the grout joints to make a better bond with the colourant. The tiles were then given a rinse and dried before I stripped out the old sealant strip between the tiles and shower tray.

My next task was to carefully apply a white Grout Colourant along the grout lines using an applicator brush. The colourant is basically painted onto the grout and any excess is wiped off the adjacent tile before it dries. The colourant, which is available in a range of shades, is an epoxy based product that both recolours and seals the grout lines to provide protection against dirt and stains.

To finish off the job I applied fresh sealant between the shower tray and bottom row of tiles in a matching white. The whole shower took on a much fresher appearance after I finished and looked transformed.

Grout Colouring Ceramic shower tiled cubicle in stafford after

My client contacted me two weeks after I completed the job to happily inform me that my work had actually solved a leakage problem that have been affecting the shower cubicle. With the addition of a robust clean, colouring and seal, my client was very pleased with the results.
 
 
Source: Professional Tile, Stone and Grout cleaning and maintenance services in Staffordshire

Restoring Discoloured White Grout

Recently, I was called to a work on a Limestone tiled floor in a house near Hove Park. Hove Park is a popular park in Hove, East Sussex, which was once opposite to the Goldstone Ground, the traditional home of Brighton and Hove Albion football club until the ground was demolished. My client informed me that the house was used a meeting place every Friday, and the high traffic of people was taking its toll on the floor.

Grout Colouring Limestone Tiled Floor in Hove Park Before Grout Colouring Limestone Tiled Floor in Hove Park Before

Cleaning a Limestone tiled floor

The floor was clearly in need of a good clean, especially the grout. You do need to take care when cleaning Limestone as it can be affected by the acidic substances you get in some cleaning products which can break down the surface of the Limestone and cause further damage. The results of my test clean showed the Limestone tiles responded well to the cleaning, but I was concerned about the grout, which was not cleaning very easily. I suspected that the grout had, in fact, been discoloured by a bleach-based cleaner, turning it grey. Bleach contains strong chemicals, so there is a good chance that any bleach-based cleaners used on tiled floors will discolour the grout over time. After discussing this issue with my client, I quoted separately for a possible grout recolour.

On the first day of working on the floor, I started the cleaning process using a black buffing pad attached to a floor buffer machine, in combination with a solution of Tile Doctor Pro-Clean, which I applied to the floor. This combination really helped to remove the heavily built up grime and dirt. Although the tiles looked great after the clean, I still wasn’t convinced by the state of the grout. After drying a test area with a heat gun, I confirmed that the grout was not continuous in colour and would need a recolour to get it back to looking its best again.

Recolouring the grout

I left the rest of the floor to dry for a period of two days, allowing any residual moisture to evaporate, before returning to recolour the grout with a white Grout Colourant which was applied using a good old fashioned toothbrush and baby wipes to remove any excess. I was careful to apply thin, even coats in order to prevent the possibility of the Colourant staining the tile.

After several hours of knee-breaking work, the recolouring was complete, and I was extremely pleased to be able to show my client the finished product. She was very happy to be able to show off the floor to her friends, which was now white all the way through, without the dark lines caused by the discoloured grout.

Grout Colouring Limestone Tiled Floor in Hove Park After

Another satisfied client.
 
 
Source: Professional Tile, Stone and Grout Cleaning service in East-Sussex

Deep Cleaning and Sealing Grout

This customer from Rushden called me in because she was having difficulty keeping the grout in her kitchen clean although the ceramic tiles themselves were fairly easy to maintain.

On speaking to the customer it became evident that the one coat of sealant that was originally applied to the grout five years ago had all but worn off and the cleaning products she was using were too strong reducing the life of the sealer and now dirty water getting into the now porous grout which was causing staining each time she mopped the floor.

Cleaning Grout Ceramic Tiles in Rushden Before

I gave the customer a quote for deep cleaning and extraction of tiles and grout lines, as they were thinking of selling the house they didn’t want to have the expense of re-colouring the grout. We decided the best course of action would be re-sealing the grout with Tile Doctor Grout Seal & Go after cleaning and this should protect it going forward.

Deep Cleaning Ceramic Tile and Grout

To get the grout clean and lift out the dirt we used Tile Doctor Pro-Clean mopped onto the floor and scrubbed into the grout lines with a stiff grout brush. The second and third pictures below show the equipment we use to deep clean and scrub the grout and to extract the water under pressure to clean the grout as best as possible.

Cleaning Grout Ceramic Tiles in Rushden During Cleaning Grout Ceramic Tiles in Rushden During

Sealing Grout

The final pictures below show the overall end result after allowing the floor to drying overnight and then sealing the grout with two coats of Tile Doctor Grout Seal & Go.

Cleaning Grout Ceramic Tiles in Rushden After Cleaning Grout Ceramic Tiles in Rushden After

I also talked the customer through Tile Doctor recommended cleaning procedures and advised her that she was entitled to a free bottle of Tile Doctor Neutral Cleaner which would keep the floor looking at its best for much longer and would not affect the grout sealant.
 
 
Source: Professional Tile, Stone and Grout maintenance service in Northamptonshire

Refreshing the Appearance of Grout

Photographs below of a Ceramic tiled floor in the kitchen of a house in the village of Houghton on the Hill near Leicester. The Ceramic tiles were fine but not unusually the grout had darkened substantially and would need to be deep cleaned to get it fresh again.

Ceramic Tile Before Cleaning Houghton on the hill

Cleaning Tile and Grout

The grout was badly stained so I decided to go with a strong dilution of Tile Doctor Remove and Go which we normally use for removing sealers but is also a very powerful cleaning product. It was run along the grout lines and tile and left to soak in before being scrubbed in with a black pad fitted to a rotary floor machine. The floor was then washed down with clean water and the process repeated until the grout was back to its original condition; the ceramic tiles looked much cleaner as well.

Sealing Grout

The tile and grout was left to dry and then then grout was sealed using Tile Doctor Ultra Seal which is a natural look sealer that I usually use on Travertine but works equally well on grout. You have to remember that the top layer of grout is actually porous and will attract dirt if left un-sealed, sealing it will ensure it keeps its appearance for much longer.

Ceramic Tile After Cleaning Houghton on the hill

 
 
Source: Tile, Stone and Grout Maintenance and Restoration in Leicestershire

Deep Cleaning and Sealing Newly Installed Grout

This customer from Titchmarsh near Kettering was unhappy that the Porcelain floor tiles that were installed in her kitchen six months prior were proving difficult to clean and that the grout line had turned from a grey to black and whatever she tried she just could not keep this floor clean. On inspection I soon discovered that no or very little sealer had been applied to the Porcelain which is not unusual as most Porcelain does not require a sealer however Micro Porous Porcelain does and she should have been advised by the shop that sold her the tiles that this was the case. A quote was given which she was happy with and I returned the following week to sort the problem out.

Deep Cleaning Porcelain Tile and Grout

To protect the kitchen units I covered them in a plastic and then moved onto to deep cleaning the tiles with a dilution of Tile doctor Pro Clean which was applied and left to soak in for a while before hand scrubbing the floor on my hands and knees with stiff brushes. This did made an improvement but something stronger was required to get the grout looking better so it was back down to the floor with hand brushes again but this time I used Tile Doctor Grout Clean-Up which is an acid that can remove grout smears and mineral deposits, in the end I actually used two litres of Grout Clean-Up to restore the grout to about 95% of its correct appearance and once done I gave the floor a thorough wash down to remove any trace of product.

Dirty Grout in Titchmarsh Kitchen During Cleaning

Sealing Porcelain Tile and Grout

This grout should have been correctly sealed from day one and luckily for the client it came up to her satisfaction otherwise the only other option would have been to use a Grout Colourant which would have been more costly but cheaper than replacing the grout altogether. Had the grout been much older this may have been the best option as I suspect the result from cleaning would have been less effective. The last step was to seal the tiles and grout using Tile Doctor Ultra Seal which is a natural look sealer that provides maximum stain protection and is recommended for use in kitchens. Before leaving I gave the client written instructions on maintenance which she found very helpful.

Dirty Grout in Titchmarsh Kitchen After Cleaning

 
 
Source: Tile, Stone and Grout problems resolved in Northamptonshire

Dealing with Darkened Grout

This was a straight forward Grout Colouring job at a house in the market town of Tamworth, Staffordshire. The tiles had been installed with a white grout and over the years the grout had become darker as the dirt had become ingrained into the porous top layer. This is often the case with Porcelain and Ceramic tiles whose looks always outlive that of the grout.

Grout Colour Before Tamworth Grout Colour Before Tamworth

Cleaning and Colouring Grout

The customer was keen to get the grouting looking the same as it was when first installed and so with that aim in mind a dilution of Tile Doctor Pro-Clean was applied and scrubbed into the grout lines and then washed off with water. Pro-Clean is a strong alkaline cleaning product that does a good job cleaning up grout however it can only do so much and in this case although it made a difference there were many areas which were too stained.

The next step was to apply a grout colouring product, they come in a number of different colours and the best match to the original colour was Ivory. The Pro-Clean had already prepared the surface so no need to use a pre-treater, it was just a question of waiting for the grout to dry and then apply the colourant.

Applying grout colourant is fiddly work but you do get the pleasure of watching the floor become slowly transformed, also the colourant works as a sealant which will prevent staining and make the grout very easy to clean going forward.

Grout Colour After Tamworth Grout Colour After Tamworth

As you can see the floor looks like new and the customer was very happy.
 
 
Source: Tile, Stone and Grout Maintenance Service in Staffordshire

Grout Colouring Wall Tiles

I recently paid a visit to a customer at a house in the town of Preston to restore the colour of the grout in their bathroom which due to years of using strong cleaning products had bleached the grout of any colour. The tiles themselves were not the issue they seemed fine but the grout was looking Tired; we discussed the options and decided the best course of action would be to apply a grout colourant. Two different colours were chosen, white for the shower area and Sandstone for the toilet area.

WC Grout Colouring in Preston Before Shower Cubicle Grout Colouring in Preston Before

Colouring Wall Grout

Before applying the grout colourant it’s important to give the grout a deep clean using the Pre-Treater that comes with the kit; the solution is sprayed on and scrubbed in by hand before being rinsed off with water.

Once the grout had dried I started to apply the Grout colour which restores the colour and seals the grout as well, thus making it easier to clean afterwards. Grout colouring is fiddly work but you do get the gratification of an instant change. Once done I called the customer in who was delighted with the new effect as Grout colour if used correctly looks very natural and not as if someone has painted the grout making it look false.

WC Grout Colouring in Preston After Shower Cubicle Grout Colouring in Preston After

We discussed using the correct type of cleaning product for aftercare as this seemed to be the issue to start with and I recommended Tile Doctor Aqua-Pro as this can be sprayed onto the Tiles and mopped off which is ideal where a small amount of water is required. For regular cleaning Tile Doctor Neutral cleaner was also mentioned as this is diluted into water where more cleaning is needed and mopped onto the floor area.
 
 
Source: Grout Colouring Service in Lancashire

Restoring the Appearance of Grout

This particular Slate tiled floor was installed in the kitchen of a house in Huston, that’s Houston near Glasgow not the city in Texas. This is another example of a natural stone floor was overdue a deep clean and re-seal, any remaining sealer on the slate has worn off and the tiles have become dull and stained.

Slate tiled floor Huston before cleaning

Cleaning Slate Floor Tile and Grout

First we stripped any remaining sealer from the slate tiles by applying a strong solution of Tile Doctor Pro-Clean which was left to soak in before being worked into the stone using a black pad on a rotary bonnet machine; the resultant soiled cleaning solution was then extracted using a wet vacuum. This process was repeated three times to make sure all the sealer and dirt was completely removed and extracted.

After this we focused on cleaning the grout using more Pro-Clean this time worked in using a stiff grout brush by hand. Once done the floor was given a thorough rinse using clean water again using the wet vacuum to remove the water and get the floor as dry as possible.

Changing the Colour of Grout

We then left for the evening to allow the floor to dry off overnight and returned the second day and coloured the grout to dark grey using a grout colouring kit to achieve an even grout appearance. This is rather painstaking work but the effect is well worth the effort, then once that had dried we gave the floor a quick clean using Tile Doctor Neutral Cleaner.

Sealing Slate Floor Tiles

After allowing to dry overnight again, we came back the third day to seal the slate tiles for which we used six coats of Tile Doctor Seal and Go which is a water based sealer (no smell) which added a nice sheen to the tile and gave the desired finish.

Slate tiled floor Huston after cleaning and sealing

 
 
Source: Tile, Stone and Grout Restoration Service in Glasgow

Changing the Colour of Grout on a Slate Tiled floor

Slate is a hard-wearing product ideal for floors however it does need a sealer to bring out the best in it and sealers do wear off after a few years and this had happened with the Slate tiled floor in this post. The floor was now looking dull and the grout had also discoloured so time to call in Tile Doctor to breathe new life into the tile and grout.

Dark slate tiled floor glasgow before cleaning

Cleaning a Slate Floor

It’s not a good idea to apply a new sealer on-top of existing as it can affect the final result so the first task was to strip back the floor to the natural stone giving the Slate and Grout a thorough clean in the process.

To do this a strong solution of Tile Doctor Tile Doctor Pro-Clean was applied and left to soak into the floor for about 20 minutes; Pro-Clean has a strong alkaline base so it’s safe to use on Stone as opposed to a weak acid cleaner. After twenty minutes it was worked into the slate and grout using a low speed bonnet machine fitted with a black scrubbing pad with the excess extracted using a wet vacuum.

This process was repeated three times to make sure all the old sealer and dirt was completely removed and after this the grout was cleaned by hand using more Pro-Clean and a stiff brush. Once done the whole floor was then neutralised with more water to ensure there was no trace of cleaning product remaining on the floor prior to sealing.

Grout Colouring

The floor was left to dry off overnight and returned the second day to colour the grout to dark grey which made a big improvement to the overall look of the floor; the grout colours we use come in 12 colours so we can usually find one that matches the customers’ requirements, once applied they also form a great barrier preventing future staining. Once the colourant has dried the floor was given a further clean with Tile Doctor Neutral Cleaner which is an everyday cleaning product we recommend for sealed floors.

Sealing a Slate Floor Sealing

The floor was left to dry and we came back two days later to re-seal the tile for which we used five coats of Tile Doctor Seal and Go which is a great sealer for Slate tiled floors as it leaves a low sheen finish whilst providing excellent stain protection. I should mention that Seal and Go is also a water based sealer so it doesn’t leave a smell whilst it’s drying.

Dark slate tiled floor glasgow after cleaning

We left the floor to dry overnight again and came back the third day to seal the Slate tiles for which we used six coats of Tile Doctor Seal and Go which give a subtle shine to the tiles and matched the customers requirements.
 
 
Source: Slate Floor Tile Cleaning

New Life For Stained Kitchen Grout

The grout on this Quarry tiled floor in the kitchen of a house in Livingston near Edinburgh was proving impossible to clean effectively and had now become badly stained with dirt and grime and had gone dark in the process making it obviously dirty when compared with the clean areas.

Quarry Tiles Before Cleaning and Colouring

Cleaning Tile and Grout

The first step when cleaning grout is to apply a strong solution of Tile Doctor Pro-Clean which is a strong alkaline cleaning agent. The solution is mopped onto the tile and grout and then scrubbed in by hand with a stiff brush along the grout lines, Pro-Clean is also a good general tile cleaner so it worked well on the Quarry Tiles as well. The soiled cleaning solution was rinsed away with water and as much water as possible was removed using a wet vacuum. Next we left the floor to allow it to dry leaving a turbo air mover in help to speed up the process.

Quarry Tiles Before Cleaning and Colouring

Sealing Quarry Tiles

When the floor was dry it was clear that the grout would never be clean enough to match with the areas that were still white so we agreed to apply a white epoxy Grout Colourant to resolve the problem. The group colourant is applied by hand and is painted onto the grout using a small brush; any excess is then wiped off the tile. Two coats were required on this floor.

Quarry Tiles After Cleaning and Colouring

The floor now looks like it has come back to life and as you can see all the grout now has a uniform colour and should stay that way for a long time as the added advantage of an epoxy grout colourant is it forms a barrier over the grout that will seal and protected it.

Quarry Tiles After Cleaning and Colouring

 
 
Source: Tile, Stone and Grout Cleaning and Sealing in Edinburgh

Tired Shower Grout Refresh

Keeping the tile and grout in shower cubicles clean is often a headache for homeowners and this cubicle at a house in Edinburgh was certainly no different. You can see from the photograph below that although the glazed ceramic tiles were in good condition they were being made to look grubby by the stained condition of the adjacent grout and there were also signs of mould build-up. If you catch this early you can overcome the problem spraying on a product called Tile Doctor Mould-Away however in this case a full refresh was required.

Shower Renovation Before Cleaning

Cleaning Ceramic Tile and Grout

We started by spraying the tile and grout down with Tile Doctor which is a strong alkaline cleaner Pro-Clean, spraying it on mixes it with helping it to stick to Vertical surfaces where it can get to work on the dirt. We left it to dwell for ten minutes before scrubbing it in by hand using a stiff grout brush; this process certainly improved the grout but unfortunately it had become too badly stained to be satisfactory so it was agreed with the owner that we would recolour the grout using a white grout colourant.

Recolouring Grout

The grout colourant comes in a tube and is very straightforward to apply although I must admit the work is quite tedious. Two coats of white colourant were required to get the uniform appearance needed and I think you will agree the effect is quite transforming. The other advantage of these particular colourant products is that they are epoxy based and form a barrier of the grout preventing future staining and making it very easy to clean going forward.

Shower Renovation After Cleaning

The last step was to carefully remove the existing silicon strip along the base of the cubicle with a sharp nice and replace with new. The final result was a shower cubicle that looked recently installed.
 
 
Source: Tile, Stone and Grout Cleaning and Sealing in Edinburgh

Recolouring Stained Grout

A customer near Maidenhead asked us to take a look at their dirty porcelain floor tile and grout which had degenerated following ten years of traffic from children and pets. Domestic cleaning products were proving ineffective and professional help was now required to get the floor looking healthy again.

Dirty Tile and Grout Resolved in Maidenhead Before Cleaning

Deep Cleaning Porcelain Tiles

To get the dirt out of the tiles they were cleaned with a very mild hot water dilution of Tile Doctor Pro-Clean which was spread over the tiles and left to soak into the tiles for twenty minutes, during this time the solution was scrubbed into the grout lines using a stiff brush.

The next step was to connect up our van mounted high pressure hot water clean and capture system (see photo below) and rinse the tiles and grout. This system produces very little water or spray because of its unique recovery system to a waste tank in our van. It also neutralises cleaning solutions and the high pressure penetrates into the pores of the tile removing all the soiling and pollutants.

Dirty Tile and Grout Resolved in Maidenhead During Cleaning

Applying Grout Colourant

The powerful pressure cleaning worked well on the tiles but unfortunately the grout lines had absorbed too much soiling and staining over the years which had become ingrained to a depth which could not be removed without replacing the grout. Fortunately there was another option which was to apply a Grout Colourant. Tile Doctor has a range of epoxy based colourant’s available in different colours which are relatively easy to apply and form a barrier over the existing grout to provide a uniform look and durable protection against future staining and discolouration

Dirty Tile and Grout Resolved in Maidenhead During Grout Colouring

The floor was ready for surface traffic in a few hours and I think you will agree the final result has restored this dirty and tired floor to a fresh, revitalised as new finish

Dirty Tile and Grout Resolved in Maidenhead After

My customer was very happy with the results and left the following testimonial:

Hi Tim, Many thanks for the amazing results you achieved with my Kitchen/Conservatory floor, I was blown away by the finish – it looks like new! Thank you for care instructions, we will make every effort to follow carefully.
Best wishes and thank you again. Ms. J Walker

 
 
Source: Grout Colouring Services in Berkshire

Cleaning Kitchen Floor Tile and Grout

We received a call to visit a house in Chorley where the grout in the kitchen tiles had gone black with the build-up of dirt and the owner was having trouble cleaning it. Porcelain and Ceramic tiles are a great choice for kitchens as they are very easy to clean however what most people don’t realise is that the top layer of grout is actually porous and can becomes stained with dirt. With the agreement of the home owner I did a test clean using a strong cleaning product called Tile Doctor Remove and Go leaving it to dwell on the tile and grout before scrubbing it in by hand and then washing off the soiled solution; you can see from the photograph below that the tile and grout cleaned up nicely so I was booked to do the job the following week.

Chorley Tile and Grout Cleaning Test

Cleaning Tile and Grout

On my return I repeated the earlier process on the whole floor cleaning the grout with Remove and Go and working it in along the grout lines with a stiff grout brush making sure to thoroughly scrub every grout joint working in small sections at a time.

Chorley Tile and Grout Before Cleaning

Once I was happy with the grout in a section the floor would be rinsed off with clean water and a wet vacuum was used to remove the dirty water. I did this all over the floor until all the grout joints were clean retreating areas that needed extra attention.

Chorley Tile and Grout During Cleaning

The next step was to give the ceramic tiles a good clean by applying a strong general Tile and Grout cleaning product called Tile Doctor Pro-Clean. The solution was scrubbed onto the floor and left to dwell for ten minutes scrubbed some more and then rinsed off. The floor was then washed down with clean water three times to make sure all the cleaning products had been removed and then dried with a wet vacuum. I then left the floor to completely dry for a couple of hours and came back later to check all the grout joints were clean and followed up with a bit of detail work on corners and edges rinsing the floor again when I had finished.

Chorley Tile and Grout After Cleaning

I managed to complete the job in a day and with all the cleaning the tile and grout came up much lighter than before making it look like a new floor had been installed. The customer was really happy with the final result and left the following feedback on the Tile Doctor feedback system.

Heidi cleaned a very dirty tiled floor back to its original state and it now looks superb. She was extremely professional and courteous but just as important she didn’t leave a mess like a lot of tradesmen do!!! I would have no hesitation in recommending Heidi to any of my friends to carry out similar work. A job well done!!!
Chris Palmer, Chorley

Chorley Tile and Grout Before and After Cleaning

 
 
Source: Residential and Commercial Tile Cleaning in Lancashire

Using Tile Doctor Mould Away

This shower cubicle was installed in the main bathroom of a house in Bishopton where the grout had become quite grubby and the Ceramic tiles were looking quite dull. The owner was thinking about re-tiling the bathroom and thought they would give us a call first to see if we could refresh the look without the expense.

Gruby Ceramic Tiled Shower in Bishopton Before Gruby Ceramic Tiled Shower in Bishopton Before

Cleaning Ceramic Tile and Grout

We started by spraying the tiles with Tile Doctor Oxy-Pro which is a strong high-alkaline cleaner especially formulated and packaged for cleaning showers. The spray delivery is important as mixing the cleaning product with air makes it lighter and helps it cling to the tile and grout. The Oxy-Pro was left to soak into the tiles for around 15 minutes before being scrubbed into the tile and grout using a stiff grout brush. This action cleaned up the grout and tile nicely removing stains from shampoos and soaps etc.

Removing Mould from Grout

The grout was looking much improved but there was however some evidence of mould remaining which needed dealing with. To tackle this we used Tile Doctor Mould Away which is designed to remove mould off Silicone and Grout. It’s very easy to use, you simply spray the Silicone or Grout to be treated with Mould Away then leave to soak in for five minutes and then scrub with a brush and rinse with water repeating the process until the mould has disappeared.

Gruby Ceramic Tiled Shower in Bishopton After Gruby Ceramic Tiled Shower in Bishopton After

It took a fair amount of manual effort but the results were well worth it as you can see.
 
 
Source: Expert Ceramic Tile Maintenance advice

Dealing with Mould and Mildew on Grout

The before and after photograph below is from a job we did in a Shower Cubicle tiled with small square Mosaic tiles at a house in Bedford. As you can see from the photograph the grout had become stained with mould and mildew growth which had become quite bad and moved onto the surface of the tile.

Cleaning Mosaic Tiles

To resolve the problem a strong dilution of Tile Doctor Pro-Clean was scrubbed into the tile and grout by hand using a stiff brush. It’s best to let the Pro-Clean soak into the tile and grout for ten minutes before working in and to help the solution stick on vertical surfaces it’s best to decant the Pro-Clean into a spray bottle and spray it onto the surface of the tile, this allows it to mix with air making it lighter and enabling it to stick to the surface instead of running off.

Mosaic Shower Tile Refresh in Bedford Before and After

The mould and mildew had become quite ingrained and had managed to get quite a foothold in the grout which due to its cementitious nature is actually porous near the surface. As a result the tiles were proving very had to get clean and so working in sections the process was repeated numerous times requiring a lot of physical effort and Pro-Clean before we were happy with the results.
 
 
Source: Residential and Commercial Stone, Tile and Grout Cleaning Services in Bedfordshire

Colouring Grout in Lancashire

A customer in Leyland near Preston reported a grouting issue with their porcelain tiled kitchen floor, the tiles were fine but the grout had become discoloured and grey, they were also finding it difficult to keep clean. This is not an unusual story for Porcelain or Ceramic tiled floors which are generally very low maintenance and you find the grout needs attention before the tiles do.

Grout Colouring in Leyland Before

Applying Grout Colourant

On arrival I set up my equipment and cleaned the floor to make sure all the grout joints were free from any dirt etc., I then did a colour test on a less obvious part of the floor with the grout colour. I wanted to make sure the colourant would take to the grout and also to make sure the customer was happy with her colour choice.

The process for grout colouring is fairly tedious but straightforward, it involves giving the bottle a good shake and applying a small amount to a toothbrush and working the grout colorant into joints using a back-and-forth motion. I find the best way to apply it is by working in small areas and adding thin even coats to limit the amount of grout colorant that gets on the tile. They were large format tiles covering 9m2 so I only needed one bottle of buff grout colourant to do the entire floor.

After the Grout Colorant dries (it takes between twenty and sixty minutes depending on how warm the house) you mist the surface with water and let stand for five minutes, excess grout colorant is then removed from the tile surface using a white nylon scrub pad.

Grout Colouring in Leyland During

The floor was ready for surface traffic in 2 hours but there was a white mist over the floor which you can get with porcelain tiles so I fitted a white buffing pad to my rotary floor polishing machine and buffed the floor to remove the power and water marks, once finished the floor looked like new. Before leaving I left the customer with some after care instructions and how to keep it floor looking good for the future.

Grout Colouring in Leyland After

 
 
Source: Making Grout look new again in Lancashire

Recolouring Kitchen Grout

This was a straightforward request to deep clean the Ceramic Tile and Grout in the kitchen of a house in Romsey, Hampshire but as you will see from the photograph below the Grout was far too stained to be cleaned effectively. Kitchen grout gets a lot of abuse from spillages so this is not unusual and to prevent it the grout can be sealed or you can choose a dark grout colour.

Romsey Ceramic Tile and Grout Before Cleaning

Cleaning and Preparing the Tile and Grout

To get the tile and grout clean I applied a dilution of Tile Doctor Pro-Clean and left it to soak in to the surface dirt for a while before scrubbing it with a rotary machine fitted with a black scrubbing pad and also a stiff hand brush along the grout lines. This was then washed down with warm water all of which was removed by a wet Vacuum. This cleaning process was repeated until the tiles were clean and the grout was a good as I could get it. Unfortunately the grout had stained quite badly and we were unable to get a good uniform appearance so after discussing this with the customer it was agreed that we would apply a white Grout Colourant.

Applying Grout Colourant

If it was a small area I could have considered using a Grout Pen however this required more than a touch up so this is where you need an epoxy grout colourant which forms a hard wearing epoxy barrier over the existing grout that looks natural and effectively protects the grout from further staining.

The grout needs to be clean and dry before you apply it so if you’re doing this from scratch make sure you clean the grout first with Pro-Clean or the Pre-Treater product that is available. The grout colourant is then easily applied using a toothbrush, it sounds easy but you have to be very methodical. The colourant dries in about an hour after which it’s worth double checking your work and then removing any excess by applying a little water and running over it with a white pad.

Romsey Ceramic Tile and Grout After Cleaning and Colouring

I think you will agree from the photographs the tiles look much cleaner and the floor transformed by the improvement in grout colour.
 
 
Source: Grout Colouring Service in Hampshire