We received a call to visit a house in Chorley where the grout in the kitchen tiles had gone black with the build-up of dirt and the owner was having trouble cleaning it. Porcelain and Ceramic tiles are a great choice for kitchens as they are very easy to clean however what most people don’t realise is that the top layer of grout is actually porous and can becomes stained with dirt. With the agreement of the home owner I did a test clean using a strong cleaning product called Tile Doctor Remove and Go leaving it to dwell on the tile and grout before scrubbing it in by hand and then washing off the soiled solution; you can see from the photograph below that the tile and grout cleaned up nicely so I was booked to do the job the following week.
Cleaning Tile and Grout
On my return I repeated the earlier process on the whole floor cleaning the grout with Remove and Go and working it in along the grout lines with a stiff grout brush making sure to thoroughly scrub every grout joint working in small sections at a time.
Once I was happy with the grout in a section the floor would be rinsed off with clean water and a wet vacuum was used to remove the dirty water. I did this all over the floor until all the grout joints were clean retreating areas that needed extra attention.
The next step was to give the ceramic tiles a good clean by applying a strong general Tile and Grout cleaning product called Tile Doctor Pro-Clean. The solution was scrubbed onto the floor and left to dwell for ten minutes scrubbed some more and then rinsed off. The floor was then washed down with clean water three times to make sure all the cleaning products had been removed and then dried with a wet vacuum. I then left the floor to completely dry for a couple of hours and came back later to check all the grout joints were clean and followed up with a bit of detail work on corners and edges rinsing the floor again when I had finished.
I managed to complete the job in a day and with all the cleaning the tile and grout came up much lighter than before making it look like a new floor had been installed. The customer was really happy with the final result and left the following feedback on the Tile Doctor feedback system.
Heidi cleaned a very dirty tiled floor back to its original state and it now looks superb. She was extremely professional and courteous but just as important she didn’t leave a mess like a lot of tradesmen do!!! I would have no hesitation in recommending Heidi to any of my friends to carry out similar work. A job well done!!! Chris Palmer, Chorley
This was a straightforward request to deep clean the Ceramic Tile and Grout in the kitchen of a house in Romsey, Hampshire but as you will see from the photograph below the Grout was far too stained to be cleaned effectively. Kitchen grout gets a lot of abuse from spillages so this is not unusual and to prevent it the grout can be sealed or you can choose a dark grout colour.
Cleaning and Preparing the Tile and Grout
To get the tile and grout clean I applied a dilution of Tile Doctor Pro-Clean and left it to soak in to the surface dirt for a while before scrubbing it with a rotary machine fitted with a black scrubbing pad and also a stiff hand brush along the grout lines. This was then washed down with warm water all of which was removed by a wet Vacuum. This cleaning process was repeated until the tiles were clean and the grout was a good as I could get it. Unfortunately the grout had stained quite badly and we were unable to get a good uniform appearance so after discussing this with the customer it was agreed that we would apply a white Grout Colourant.
Applying Grout Colourant
If it was a small area I could have considered using a Grout Pen however this required more than a touch up so this is where you need an epoxy grout colourant which forms a hard wearing epoxy barrier over the existing grout that looks natural and effectively protects the grout from further staining.
The grout needs to be clean and dry before you apply it so if you’re doing this from scratch make sure you clean the grout first with Pro-Clean or the Pre-Treater product that is available. The grout colourant is then easily applied using a toothbrush, it sounds easy but you have to be very methodical. The colourant dries in about an hour after which it’s worth double checking your work and then removing any excess by applying a little water and running over it with a white pad.
I think you will agree from the photographs the tiles look much cleaner and the floor transformed by the improvement in grout colour.
This Ceramic tiled family bathroom with shower was installed at house in Leighton Buzzard and was in need of rejuvenation. You can see from the photograph below that the tiles were in reasonable condition but the grout had become ingrained with dirt which is not unknown as the top layer of grout is porous and will discolour over time if not protected.
Cleaning Ceramic Tile and Grout
The Ceramic tiles and grout were treated using a strong 2:1 dilution of Tile Doctor Pro-Clean mixed 50/50 with Nanotech Ultraclean which combines a highly powerful Tile and Grout cleaning product with tiny abrasive particles. For vertical tiled surfaces I recommend the mixture is decanted into a bottle with a trigger spray attachment which when sprayed onto the wall allows the cleaner to mix with air making it lighter and allowing it to stick better. The solution was then worked in using a stiff scrubbing brush by hand before being rinsed off with water; this process was repeated a number of times until we had managed to clean all the areas and then left to dry.
The grout was dried and the sealed with a couple of coats of Tile Doctor Grout Sealer which forms a protective barrier over the porous grout and keeps it looking good for longer. Most sealers can be used on grout (check the label to confirm) but for best results use a spray bottle as mixing the sealer with air improves its ability to stick to a vertical surface.
A customer in Kendal requested that the colour of grout installed on 20m2 newly laid textured Porcelain tile floor was changed; the tiler had used a Sandstone coloured grout and they were not happy with the colour or the grouting in general which looked patchy. I recommended the use of an epoxy Grout Colouring product that re-colours, seals and rejuvenates existing grout joints and comes in twelve different colours and after showing the customer the different colour options they picked Charcoal Grey.
Applying Grout Colourant
I did a test area so they could see how it might look under the lights which went well and so I started to apply the grout colouring to the whole kitchen floor completing small areas until the entire floor was covered and taking care not to get any on the Porcelain tile as the textured surface makes it difficult to remove and requires the use of an white abrasive scouring pad. Normally you have to use a Pre-Treater product on the grout before Grout Colouring however this grout was new and so this step was unnecessary.
This job took me one day and only required one tube of Grout Colourant. The owner was extremely happy with the result will now have a fairly maintenance free tiled floor as Porcelain tiles are very hard wearing and the epoxy grout colourant acts as a barrier and therefore unlikely to discolour.