Refreshing the Appearance of Grout

Photographs below of a Ceramic tiled floor in the kitchen of a house in the village of Houghton on the Hill near Leicester. The Ceramic tiles were fine but not unusually the grout had darkened substantially and would need to be deep cleaned to get it fresh again.

Ceramic Tile Before Cleaning Houghton on the hill

Cleaning Tile and Grout

The grout was badly stained so I decided to go with a strong dilution of Tile Doctor Remove and Go which we normally use for removing sealers but is also a very powerful cleaning product. It was run along the grout lines and tile and left to soak in before being scrubbed in with a black pad fitted to a rotary floor machine. The floor was then washed down with clean water and the process repeated until the grout was back to its original condition; the ceramic tiles looked much cleaner as well.

Sealing Grout

The tile and grout was left to dry and then then grout was sealed using Tile Doctor Ultra Seal which is a natural look sealer that I usually use on Travertine but works equally well on grout. You have to remember that the top layer of grout is actually porous and will attract dirt if left un-sealed, sealing it will ensure it keeps its appearance for much longer.

Ceramic Tile After Cleaning Houghton on the hill

 
 
Source: Tile, Stone and Grout Maintenance and Restoration in Leicestershire

Deep Cleaning and Sealing Newly Installed Grout

This customer from Titchmarsh near Kettering was unhappy that the Porcelain floor tiles that were installed in her kitchen six months prior were proving difficult to clean and that the grout line had turned from a grey to black and whatever she tried she just could not keep this floor clean. On inspection I soon discovered that no or very little sealer had been applied to the Porcelain which is not unusual as most Porcelain does not require a sealer however Micro Porous Porcelain does and she should have been advised by the shop that sold her the tiles that this was the case. A quote was given which she was happy with and I returned the following week to sort the problem out.

Deep Cleaning Porcelain Tile and Grout

To protect the kitchen units I covered them in a plastic and then moved onto to deep cleaning the tiles with a dilution of Tile doctor Pro Clean which was applied and left to soak in for a while before hand scrubbing the floor on my hands and knees with stiff brushes. This did made an improvement but something stronger was required to get the grout looking better so it was back down to the floor with hand brushes again but this time I used Tile Doctor Grout Clean-Up which is an acid that can remove grout smears and mineral deposits, in the end I actually used two litres of Grout Clean-Up to restore the grout to about 95% of its correct appearance and once done I gave the floor a thorough wash down to remove any trace of product.

Dirty Grout in Titchmarsh Kitchen During Cleaning

Sealing Porcelain Tile and Grout

This grout should have been correctly sealed from day one and luckily for the client it came up to her satisfaction otherwise the only other option would have been to use a Grout Colourant which would have been more costly but cheaper than replacing the grout altogether. Had the grout been much older this may have been the best option as I suspect the result from cleaning would have been less effective. The last step was to seal the tiles and grout using Tile Doctor Ultra Seal which is a natural look sealer that provides maximum stain protection and is recommended for use in kitchens. Before leaving I gave the client written instructions on maintenance which she found very helpful.

Dirty Grout in Titchmarsh Kitchen After Cleaning

 
 
Source: Tile, Stone and Grout problems resolved in Northamptonshire

Dealing with Darkened Grout

This was a straight forward Grout Colouring job at a house in the market town of Tamworth, Staffordshire. The tiles had been installed with a white grout and over the years the grout had become darker as the dirt had become ingrained into the porous top layer. This is often the case with Porcelain and Ceramic tiles whose looks always outlive that of the grout.

Grout Colour Before Tamworth Grout Colour Before Tamworth

Cleaning and Colouring Grout

The customer was keen to get the grouting looking the same as it was when first installed and so with that aim in mind a dilution of Tile Doctor Pro-Clean was applied and scrubbed into the grout lines and then washed off with water. Pro-Clean is a strong alkaline cleaning product that does a good job cleaning up grout however it can only do so much and in this case although it made a difference there were many areas which were too stained.

The next step was to apply a grout colouring product, they come in a number of different colours and the best match to the original colour was Ivory. The Pro-Clean had already prepared the surface so no need to use a pre-treater, it was just a question of waiting for the grout to dry and then apply the colourant.

Applying grout colourant is fiddly work but you do get the pleasure of watching the floor become slowly transformed, also the colourant works as a sealant which will prevent staining and make the grout very easy to clean going forward.

Grout Colour After Tamworth Grout Colour After Tamworth

As you can see the floor looks like new and the customer was very happy.
 
 
Source: Tile, Stone and Grout Maintenance Service in Staffordshire

Grout Colouring Wall Tiles

I recently paid a visit to a customer at a house in the town of Preston to restore the colour of the grout in their bathroom which due to years of using strong cleaning products had bleached the grout of any colour. The tiles themselves were not the issue they seemed fine but the grout was looking Tired; we discussed the options and decided the best course of action would be to apply a grout colourant. Two different colours were chosen, white for the shower area and Sandstone for the toilet area.

WC Grout Colouring in Preston Before Shower Cubicle Grout Colouring in Preston Before

Colouring Wall Grout

Before applying the grout colourant it’s important to give the grout a deep clean using the Pre-Treater that comes with the kit; the solution is sprayed on and scrubbed in by hand before being rinsed off with water.

Once the grout had dried I started to apply the Grout colour which restores the colour and seals the grout as well, thus making it easier to clean afterwards. Grout colouring is fiddly work but you do get the gratification of an instant change. Once done I called the customer in who was delighted with the new effect as Grout colour if used correctly looks very natural and not as if someone has painted the grout making it look false.

WC Grout Colouring in Preston After Shower Cubicle Grout Colouring in Preston After

We discussed using the correct type of cleaning product for aftercare as this seemed to be the issue to start with and I recommended Tile Doctor Aqua-Pro as this can be sprayed onto the Tiles and mopped off which is ideal where a small amount of water is required. For regular cleaning Tile Doctor Neutral cleaner was also mentioned as this is diluted into water where more cleaning is needed and mopped onto the floor area.
 
 
Source: Grout Colouring Service in Lancashire

Restoring the Appearance of Grout

This particular Slate tiled floor was installed in the kitchen of a house in Huston, that’s Houston near Glasgow not the city in Texas. This is another example of a natural stone floor was overdue a deep clean and re-seal, any remaining sealer on the slate has worn off and the tiles have become dull and stained.

Slate tiled floor Huston before cleaning

Cleaning Slate Floor Tile and Grout

First we stripped any remaining sealer from the slate tiles by applying a strong solution of Tile Doctor Pro-Clean which was left to soak in before being worked into the stone using a black pad on a rotary bonnet machine; the resultant soiled cleaning solution was then extracted using a wet vacuum. This process was repeated three times to make sure all the sealer and dirt was completely removed and extracted.

After this we focused on cleaning the grout using more Pro-Clean this time worked in using a stiff grout brush by hand. Once done the floor was given a thorough rinse using clean water again using the wet vacuum to remove the water and get the floor as dry as possible.

Changing the Colour of Grout

We then left for the evening to allow the floor to dry off overnight and returned the second day and coloured the grout to dark grey using a grout colouring kit to achieve an even grout appearance. This is rather painstaking work but the effect is well worth the effort, then once that had dried we gave the floor a quick clean using Tile Doctor Neutral Cleaner.

Sealing Slate Floor Tiles

After allowing to dry overnight again, we came back the third day to seal the slate tiles for which we used six coats of Tile Doctor Seal and Go which is a water based sealer (no smell) which added a nice sheen to the tile and gave the desired finish.

Slate tiled floor Huston after cleaning and sealing

 
 
Source: Tile, Stone and Grout Restoration Service in Glasgow

Changing the Colour of Grout on a Slate Tiled floor

Slate is a hard-wearing product ideal for floors however it does need a sealer to bring out the best in it and sealers do wear off after a few years and this had happened with the Slate tiled floor in this post. The floor was now looking dull and the grout had also discoloured so time to call in Tile Doctor to breathe new life into the tile and grout.

Dark slate tiled floor glasgow before cleaning

Cleaning a Slate Floor

It’s not a good idea to apply a new sealer on-top of existing as it can affect the final result so the first task was to strip back the floor to the natural stone giving the Slate and Grout a thorough clean in the process.

To do this a strong solution of Tile Doctor Tile Doctor Pro-Clean was applied and left to soak into the floor for about 20 minutes; Pro-Clean has a strong alkaline base so it’s safe to use on Stone as opposed to a weak acid cleaner. After twenty minutes it was worked into the slate and grout using a low speed bonnet machine fitted with a black scrubbing pad with the excess extracted using a wet vacuum.

This process was repeated three times to make sure all the old sealer and dirt was completely removed and after this the grout was cleaned by hand using more Pro-Clean and a stiff brush. Once done the whole floor was then neutralised with more water to ensure there was no trace of cleaning product remaining on the floor prior to sealing.

Grout Colouring

The floor was left to dry off overnight and returned the second day to colour the grout to dark grey which made a big improvement to the overall look of the floor; the grout colours we use come in 12 colours so we can usually find one that matches the customers’ requirements, once applied they also form a great barrier preventing future staining. Once the colourant has dried the floor was given a further clean with Tile Doctor Neutral Cleaner which is an everyday cleaning product we recommend for sealed floors.

Sealing a Slate Floor Sealing

The floor was left to dry and we came back two days later to re-seal the tile for which we used five coats of Tile Doctor Seal and Go which is a great sealer for Slate tiled floors as it leaves a low sheen finish whilst providing excellent stain protection. I should mention that Seal and Go is also a water based sealer so it doesn’t leave a smell whilst it’s drying.

Dark slate tiled floor glasgow after cleaning

We left the floor to dry overnight again and came back the third day to seal the Slate tiles for which we used six coats of Tile Doctor Seal and Go which give a subtle shine to the tiles and matched the customers requirements.
 
 
Source: Slate Floor Tile Cleaning

New Life For Stained Kitchen Grout

The grout on this Quarry tiled floor in the kitchen of a house in Livingston near Edinburgh was proving impossible to clean effectively and had now become badly stained with dirt and grime and had gone dark in the process making it obviously dirty when compared with the clean areas.

Quarry Tiles Before Cleaning and Colouring

Cleaning Tile and Grout

The first step when cleaning grout is to apply a strong solution of Tile Doctor Pro-Clean which is a strong alkaline cleaning agent. The solution is mopped onto the tile and grout and then scrubbed in by hand with a stiff brush along the grout lines, Pro-Clean is also a good general tile cleaner so it worked well on the Quarry Tiles as well. The soiled cleaning solution was rinsed away with water and as much water as possible was removed using a wet vacuum. Next we left the floor to allow it to dry leaving a turbo air mover in help to speed up the process.

Quarry Tiles Before Cleaning and Colouring

Sealing Quarry Tiles

When the floor was dry it was clear that the grout would never be clean enough to match with the areas that were still white so we agreed to apply a white epoxy Grout Colourant to resolve the problem. The group colourant is applied by hand and is painted onto the grout using a small brush; any excess is then wiped off the tile. Two coats were required on this floor.

Quarry Tiles After Cleaning and Colouring

The floor now looks like it has come back to life and as you can see all the grout now has a uniform colour and should stay that way for a long time as the added advantage of an epoxy grout colourant is it forms a barrier over the grout that will seal and protected it.

Quarry Tiles After Cleaning and Colouring

 
 
Source: Tile, Stone and Grout Cleaning and Sealing in Edinburgh

Tired Shower Grout Refresh

Keeping the tile and grout in shower cubicles clean is often a headache for homeowners and this cubicle at a house in Edinburgh was certainly no different. You can see from the photograph below that although the glazed ceramic tiles were in good condition they were being made to look grubby by the stained condition of the adjacent grout and there were also signs of mould build-up. If you catch this early you can overcome the problem spraying on a product called Tile Doctor Mould-Away however in this case a full refresh was required.

Shower Renovation Before Cleaning

Cleaning Ceramic Tile and Grout

We started by spraying the tile and grout down with Tile Doctor which is a strong alkaline cleaner Pro-Clean, spraying it on mixes it with helping it to stick to Vertical surfaces where it can get to work on the dirt. We left it to dwell for ten minutes before scrubbing it in by hand using a stiff grout brush; this process certainly improved the grout but unfortunately it had become too badly stained to be satisfactory so it was agreed with the owner that we would recolour the grout using a white grout colourant.

Recolouring Grout

The grout colourant comes in a tube and is very straightforward to apply although I must admit the work is quite tedious. Two coats of white colourant were required to get the uniform appearance needed and I think you will agree the effect is quite transforming. The other advantage of these particular colourant products is that they are epoxy based and form a barrier of the grout preventing future staining and making it very easy to clean going forward.

Shower Renovation After Cleaning

The last step was to carefully remove the existing silicon strip along the base of the cubicle with a sharp nice and replace with new. The final result was a shower cubicle that looked recently installed.
 
 
Source: Tile, Stone and Grout Cleaning and Sealing in Edinburgh

Recolouring Stained Grout

A customer near Maidenhead asked us to take a look at their dirty porcelain floor tile and grout which had degenerated following ten years of traffic from children and pets. Domestic cleaning products were proving ineffective and professional help was now required to get the floor looking healthy again.

Dirty Tile and Grout Resolved in Maidenhead Before Cleaning

Deep Cleaning Porcelain Tiles

To get the dirt out of the tiles they were cleaned with a very mild hot water dilution of Tile Doctor Pro-Clean which was spread over the tiles and left to soak into the tiles for twenty minutes, during this time the solution was scrubbed into the grout lines using a stiff brush.

The next step was to connect up our van mounted high pressure hot water clean and capture system (see photo below) and rinse the tiles and grout. This system produces very little water or spray because of its unique recovery system to a waste tank in our van. It also neutralises cleaning solutions and the high pressure penetrates into the pores of the tile removing all the soiling and pollutants.

Dirty Tile and Grout Resolved in Maidenhead During Cleaning

Applying Grout Colourant

The powerful pressure cleaning worked well on the tiles but unfortunately the grout lines had absorbed too much soiling and staining over the years which had become ingrained to a depth which could not be removed without replacing the grout. Fortunately there was another option which was to apply a Grout Colourant. Tile Doctor has a range of epoxy based colourant’s available in different colours which are relatively easy to apply and form a barrier over the existing grout to provide a uniform look and durable protection against future staining and discolouration

Dirty Tile and Grout Resolved in Maidenhead During Grout Colouring

The floor was ready for surface traffic in a few hours and I think you will agree the final result has restored this dirty and tired floor to a fresh, revitalised as new finish

Dirty Tile and Grout Resolved in Maidenhead After

My customer was very happy with the results and left the following testimonial:

Hi Tim, Many thanks for the amazing results you achieved with my Kitchen/Conservatory floor, I was blown away by the finish – it looks like new! Thank you for care instructions, we will make every effort to follow carefully.
Best wishes and thank you again. Ms. J Walker

 
 
Source: Grout Colouring Services in Berkshire

Cleaning Kitchen Floor Tile and Grout

We received a call to visit a house in Chorley where the grout in the kitchen tiles had gone black with the build-up of dirt and the owner was having trouble cleaning it. Porcelain and Ceramic tiles are a great choice for kitchens as they are very easy to clean however what most people don’t realise is that the top layer of grout is actually porous and can becomes stained with dirt. With the agreement of the home owner I did a test clean using a strong cleaning product called Tile Doctor Remove and Go leaving it to dwell on the tile and grout before scrubbing it in by hand and then washing off the soiled solution; you can see from the photograph below that the tile and grout cleaned up nicely so I was booked to do the job the following week.

Chorley Tile and Grout Cleaning Test

Cleaning Tile and Grout

On my return I repeated the earlier process on the whole floor cleaning the grout with Remove and Go and working it in along the grout lines with a stiff grout brush making sure to thoroughly scrub every grout joint working in small sections at a time.

Chorley Tile and Grout Before Cleaning

Once I was happy with the grout in a section the floor would be rinsed off with clean water and a wet vacuum was used to remove the dirty water. I did this all over the floor until all the grout joints were clean retreating areas that needed extra attention.

Chorley Tile and Grout During Cleaning

The next step was to give the ceramic tiles a good clean by applying a strong general Tile and Grout cleaning product called Tile Doctor Pro-Clean. The solution was scrubbed onto the floor and left to dwell for ten minutes scrubbed some more and then rinsed off. The floor was then washed down with clean water three times to make sure all the cleaning products had been removed and then dried with a wet vacuum. I then left the floor to completely dry for a couple of hours and came back later to check all the grout joints were clean and followed up with a bit of detail work on corners and edges rinsing the floor again when I had finished.

Chorley Tile and Grout After Cleaning

I managed to complete the job in a day and with all the cleaning the tile and grout came up much lighter than before making it look like a new floor had been installed. The customer was really happy with the final result and left the following feedback on the Tile Doctor feedback system.

Heidi cleaned a very dirty tiled floor back to its original state and it now looks superb. She was extremely professional and courteous but just as important she didn’t leave a mess like a lot of tradesmen do!!! I would have no hesitation in recommending Heidi to any of my friends to carry out similar work. A job well done!!!
Chris Palmer, Chorley

Chorley Tile and Grout Before and After Cleaning

 
 
Source: Residential and Commercial Tile Cleaning in Lancashire

Using Tile Doctor Mould Away

This shower cubicle was installed in the main bathroom of a house in Bishopton where the grout had become quite grubby and the Ceramic tiles were looking quite dull. The owner was thinking about re-tiling the bathroom and thought they would give us a call first to see if we could refresh the look without the expense.

Gruby Ceramic Tiled Shower in Bishopton Before Gruby Ceramic Tiled Shower in Bishopton Before

Cleaning Ceramic Tile and Grout

We started by spraying the tiles with Tile Doctor Oxy-Pro which is a strong high-alkaline cleaner especially formulated and packaged for cleaning showers. The spray delivery is important as mixing the cleaning product with air makes it lighter and helps it cling to the tile and grout. The Oxy-Pro was left to soak into the tiles for around 15 minutes before being scrubbed into the tile and grout using a stiff grout brush. This action cleaned up the grout and tile nicely removing stains from shampoos and soaps etc.

Removing Mould from Grout

The grout was looking much improved but there was however some evidence of mould remaining which needed dealing with. To tackle this we used Tile Doctor Mould Away which is designed to remove mould off Silicone and Grout. It’s very easy to use, you simply spray the Silicone or Grout to be treated with Mould Away then leave to soak in for five minutes and then scrub with a brush and rinse with water repeating the process until the mould has disappeared.

Gruby Ceramic Tiled Shower in Bishopton After Gruby Ceramic Tiled Shower in Bishopton After

It took a fair amount of manual effort but the results were well worth it as you can see.
 
 
Source: Expert Ceramic Tile Maintenance advice

Dealing with Mould and Mildew on Grout

The before and after photograph below is from a job we did in a Shower Cubicle tiled with small square Mosaic tiles at a house in Bedford. As you can see from the photograph the grout had become stained with mould and mildew growth which had become quite bad and moved onto the surface of the tile.

Cleaning Mosaic Tiles

To resolve the problem a strong dilution of Tile Doctor Pro-Clean was scrubbed into the tile and grout by hand using a stiff brush. It’s best to let the Pro-Clean soak into the tile and grout for ten minutes before working in and to help the solution stick on vertical surfaces it’s best to decant the Pro-Clean into a spray bottle and spray it onto the surface of the tile, this allows it to mix with air making it lighter and enabling it to stick to the surface instead of running off.

Mosaic Shower Tile Refresh in Bedford Before and After

The mould and mildew had become quite ingrained and had managed to get quite a foothold in the grout which due to its cementitious nature is actually porous near the surface. As a result the tiles were proving very had to get clean and so working in sections the process was repeated numerous times requiring a lot of physical effort and Pro-Clean before we were happy with the results.
 
 
Source: Residential and Commercial Stone, Tile and Grout Cleaning Services in Bedfordshire

Colouring Grout in Lancashire

A customer in Leyland near Preston reported a grouting issue with their porcelain tiled kitchen floor, the tiles were fine but the grout had become discoloured and grey, they were also finding it difficult to keep clean. This is not an unusual story for Porcelain or Ceramic tiled floors which are generally very low maintenance and you find the grout needs attention before the tiles do.

Grout Colouring in Leyland Before

Applying Grout Colourant

On arrival I set up my equipment and cleaned the floor to make sure all the grout joints were free from any dirt etc., I then did a colour test on a less obvious part of the floor with the grout colour. I wanted to make sure the colourant would take to the grout and also to make sure the customer was happy with her colour choice.

The process for grout colouring is fairly tedious but straightforward, it involves giving the bottle a good shake and applying a small amount to a toothbrush and working the grout colorant into joints using a back-and-forth motion. I find the best way to apply it is by working in small areas and adding thin even coats to limit the amount of grout colorant that gets on the tile. They were large format tiles covering 9m2 so I only needed one bottle of buff grout colourant to do the entire floor.

After the Grout Colorant dries (it takes between twenty and sixty minutes depending on how warm the house) you mist the surface with water and let stand for five minutes, excess grout colorant is then removed from the tile surface using a white nylon scrub pad.

Grout Colouring in Leyland During

The floor was ready for surface traffic in 2 hours but there was a white mist over the floor which you can get with porcelain tiles so I fitted a white buffing pad to my rotary floor polishing machine and buffed the floor to remove the power and water marks, once finished the floor looked like new. Before leaving I left the customer with some after care instructions and how to keep it floor looking good for the future.

Grout Colouring in Leyland After

 
 
Source: Making Grout look new again in Lancashire

Recolouring Kitchen Grout

This was a straightforward request to deep clean the Ceramic Tile and Grout in the kitchen of a house in Romsey, Hampshire but as you will see from the photograph below the Grout was far too stained to be cleaned effectively. Kitchen grout gets a lot of abuse from spillages so this is not unusual and to prevent it the grout can be sealed or you can choose a dark grout colour.

Romsey Ceramic Tile and Grout Before Cleaning

Cleaning and Preparing the Tile and Grout

To get the tile and grout clean I applied a dilution of Tile Doctor Pro-Clean and left it to soak in to the surface dirt for a while before scrubbing it with a rotary machine fitted with a black scrubbing pad and also a stiff hand brush along the grout lines. This was then washed down with warm water all of which was removed by a wet Vacuum. This cleaning process was repeated until the tiles were clean and the grout was a good as I could get it. Unfortunately the grout had stained quite badly and we were unable to get a good uniform appearance so after discussing this with the customer it was agreed that we would apply a white Grout Colourant.

Applying Grout Colourant

If it was a small area I could have considered using a Grout Pen however this required more than a touch up so this is where you need an epoxy grout colourant which forms a hard wearing epoxy barrier over the existing grout that looks natural and effectively protects the grout from further staining.

The grout needs to be clean and dry before you apply it so if you’re doing this from scratch make sure you clean the grout first with Pro-Clean or the Pre-Treater product that is available. The grout colourant is then easily applied using a toothbrush, it sounds easy but you have to be very methodical. The colourant dries in about an hour after which it’s worth double checking your work and then removing any excess by applying a little water and running over it with a white pad.

Romsey Ceramic Tile and Grout After Cleaning and Colouring

I think you will agree from the photographs the tiles look much cleaner and the floor transformed by the improvement in grout colour.
 
 
Source: Grout Colouring Service in Hampshire

Dirty Grout Problems Resolved

This Ceramic tiled family bathroom with shower was installed at house in Leighton Buzzard and was in need of rejuvenation. You can see from the photograph below that the tiles were in reasonable condition but the grout had become ingrained with dirt which is not unknown as the top layer of grout is porous and will discolour over time if not protected.

Cleaning Ceramic Tile and Grout

The Ceramic tiles and grout were treated using a strong 2:1 dilution of Tile Doctor Pro-Clean mixed 50/50 with Nanotech Ultraclean which combines a highly powerful Tile and Grout cleaning product with tiny abrasive particles. For vertical tiled surfaces I recommend the mixture is decanted into a bottle with a trigger spray attachment which when sprayed onto the wall allows the cleaner to mix with air making it lighter and allowing it to stick better. The solution was then worked in using a stiff scrubbing brush by hand before being rinsed off with water; this process was repeated a number of times until we had managed to clean all the areas and then left to dry.

Ceramic-Tiled-Shower-Before-and-After-Leighton-Buzzard

Sealing Grout

The grout was dried and the sealed with a couple of coats of Tile Doctor Grout Sealer which forms a protective barrier over the porous grout and keeps it looking good for longer. Most sealers can be used on grout (check the label to confirm) but for best results use a spray bottle as mixing the sealer with air improves its ability to stick to a vertical surface.
 
 
Source: Ceramic Tile and Grout cleaning tips

Choosing a Sealer for Terracotta tiles

A customer in Kendal requested that the colour of grout installed on 20m2 newly laid textured Porcelain tile floor was changed; the tiler had used a Sandstone coloured grout and they were not happy with the colour or the grouting in general which looked patchy. I recommended the use of an epoxy Grout Colouring product that re-colours, seals and rejuvenates existing grout joints and comes in twelve different colours and after showing the customer the different colour options they picked Charcoal Grey.

Textured Porcelain Tile with Limestone Grout in Kendal

Applying Grout Colourant

I did a test area so they could see how it might look under the lights which went well and so I started to apply the grout colouring to the whole kitchen floor completing small areas until the entire floor was covered and taking care not to get any on the Porcelain tile as the textured surface makes it difficult to remove and requires the use of an white abrasive scouring pad. Normally you have to use a Pre-Treater product on the grout before Grout Colouring however this grout was new and so this step was unnecessary.

Textured Porcelain Tile with Charcoal Grey Grout in Kendal Textured Porcelain Tile with Charcoal Grey Grout in Kendal53

This job took me one day and only required one tube of Grout Colourant. The owner was extremely happy with the result will now have a fairly maintenance free tiled floor as Porcelain tiles are very hard wearing and the epoxy grout colourant acts as a barrier and therefore unlikely to discolour.
 
 

Sealing Terracotta Tiles in North Cumbria

Protecting Grout on a Ceramic Tiled Kitchen Worktop

Following a referral from customer which is always nice to have, we paid a visit to a house in Brighton where the owner was having difficulty keeping their ceramic tiled kitchen worktop clean. As you can see from the photograph below the glazed ceramic tiles were in reasonable condition, it was the grout that was the problem; this is not unusual as glazer ceramics are very hard wearing but the top layer of grout is in fact porous and will trap dirt and become discoloured if not sealed.

Kitchen Tiled Worktop in Brighton Before Cleaning

Grout Cleaning

There were two ways this job could have been tackled, the first being to remove the top layer or grout using the flat blade of a screwdriver and then re-grout. It was a reasonably large area of worktop so this would have taken some time. The second and simpler option is to use a heavy duty tile and grout cleaning product such as Tile Doctor Pro-Clean and that is exactly what we did, it also has the added advantage of cleaning the tiles at the same time.

The Pro-Clean was diluted with water and then left to dwell on the tile and grout for about ten minutes before being scrubbed in by hand with a stiff brush. For the wall tiles the solution was decanted to a spray bottle and sprayed onto the tiles, the combination with air makes it lighter and more able to stick to a vertical surface.

The tiles were then washed down with water and any stubborn areas re-treated with more Pro-Clean and elbow grease, it wasn’t long before the tile and grout was looking like new again.

Sealing Grout

Now glazed Ceramic tiles don’t need to be sealed as the glaze provides an effective barrier however as I mentioned before the top layer of grout is porous and will attract dirt over time and should be sealed, especially considering kitchen worktops are used to prepare food. Tile Doctor have a range of sealing products any of which will seal grout however in this case I used Grout Seal and Go which comes in a spray bottle.

Kitchen Tiled Worktop in Brighton After Cleaning

 
 
Source: Cleaning ceramic tiles and grout in Brighton

Changing the colour of Grout

The home owner of this house in Stockbridge had become increasingly unhappy with the state of their ceramic tiled floor and we were asked to come in and give the ceramic tile and grout a thorough deep clean.

Floor Ceramic Tiles Before Stockbridge

Cleaning and Preparing the Tile and Grout

To get the tile and grout clean I applied a dilution of Tile Doctor Pro-Clean and left it to soak in to the surface dirt for a while before scrubbing it with a rotary machine fitted with a black scrubbing pad and also a stiff hand brush along the grout lines. This was then washed down with warm water all of which was removed by a wet Vacuum. This cleaning process was repeated until the tiles were clean and the grout was a good as I could get it. Unfortunately the grout had stained quite badly and we were unable to get a good uniform appearance so it was agreed that we would applying a white Grout Colourant.

Applying Grout Colourant

The grout colourant range sold by Tile Doctor are a huge improvement on those grout pens you will find in DIY stores, they come in a range of colours and form a hard wearing epoxy barrier over the existing grout that looks natural and effectively protects the grout from further staining.

The grout needs to be clean and dry before you apply it so if you’re doing this from scratch make sure you clean the grout first with Pro-Clean or the Pre-Treater product that is available. The grout colourant is then easily applied using a toothbrush, it sounds easy but you have to be very methodical. The colourant dries in about an hour after which it’s worth double checking your work and then removing any excess by applying a little water and running over it with a white pad.

Floor Ceramic Tiles After Stockbridge

I think you will agree from the photographs the tiles look much cleaner and the change in grout colour makes the floor look that much fresher, it will also be a lot easier to maintain going forward.
 
 
Source: Grout cleaning and colouring Hampshire

Colouring Grout in a Ceramic Tiled Bathroom

This Ceramic tiled shower cubicle was installed at house in Birmingham, although the Ceramic tiles were in reasonable condition the customer wanted the grout to be refreshed. Ten years ago it would have been necessary to scrape out the top layer of grout and replace however the modern grout colourant kits allow you to achieve the same effects for a lot less expense.

Grout Colouring Bathroom Before Grout Colouring Bathroom Before

Cleaning Tile and Grout

The first job was to clean the grouting with a dilution of Tile Doctor Pro-Clean worked in by hand using a scrubbing brush, we also removed the towel radiator on one wall to make sure we could get to the grout behind. Pro-Clean is a very effective tile and grout cleaner that’s good at getting grease & grime out of the grouting, this process also provides a good foundation for the grout colourant which needs a clean surface. If you’re cleaning the grout yourself you may want to consider using Tile Doctor Oxy-Pro instead as it’s a similar product that is ready to use.

Once the grout was dry Grout Colourant in a Linen colour was applied into the grout lines and the excess wiped off, I then cleaned off all the excess Grout Colourant from the tile surface and gave the tiles a good clean. As you can see it made a big difference to the bathroom and I think you will agree the choice of Linen colourant worked well and blended in well with the colour of the tiles needless to say the customer was delighted.

Grout Colouring Bathroom After Grout Colouring Bathroom After

I should mention that the Grout Colourant range supplied by Tile Doctor also seals the grout preventing it from staining and therefore ensuring it will look good for some time to come.
 
 
Source: Grout Colouring service in Staffordshire

Deep Cleaning Porcelain Tile and Grout Lines

This Porcelain hallway and kitchen floor in Teddington, Middlesex, had extensive soiling in the grout lines and some staining on some of the Porcelain tiles from drink spillages. Porcelain is very robust material but like any surface the sooner you clean-up a spillage the less staining you are likely to experience.

Porcelain Tile and Grout Before Cleaning

Cleaning Porcelain Tile and Grout

To clean the tile and grout I applied a dilution of Tile Doctor Pro-Clean, which is an effective Tile and Grout cleaner, with a mop and left it to soak in for a while before working it into the floor using a rotary machine fitted with a black scrubbing pad and a stiff brush along the grout lines. The soiled cleaning solution was removed using a wet vacuum and rinsed down with clean water. This process was repeated until I was satisfied the tile and grout was clean.

I then waited for the floor to dry before applying a coat of Tile Doctor Grout Sealer to the grout lines in order to help make future maintenance easier, this type of Porcelain did not need sealing so only the grout would benefit from this preventative measure. The process is very straightforward and can be sprayed onto the grout line wiping off the excess from the adjacent tile within a few minutes.

Porcelain and Grout After Cleaning

I think you will agree from the photographs that the grout which was very prominent has now almost disappeared restoring the floor to its original appearance.
 
 
Source: Deep cleaning Porecelain and Tile Grout in Middlesex

Grout Cleaning and Colouring in Preston, Lancashire

Oddly Enough I had sold these Ceramic tiles to the customer in Preston when I used to work at a local Tile Shop many years prior. I had also been back to clean and seal the grout on his floor tiles originally in 2007 and then again in January 2010 when we used a Grout Colourant on them. It’s nice to get called back like this as it shows they appreciate the service you provide; for this visit the request was to freshen up the floor tiles and also the Ceramic Kitchen wall tile and Grout which had become ingrained with Grease from the cooker.

Grout colouring Preston Ceramic Wall Tile Before

Cleaning Tile and Grout

The total area was approximately 25m2 and it took me a day and half to give the Tile and Grout a deep clean. For the most part I used Tile Doctor Pro-Clean but for the wall tiles where Grout Colourant has been applied I used Tile Doctor OxyPro which is a ready to use Tile and Grout cleaner that comes in a spray bottle, when applying any liquid to a wall its best to mix it with air in a spray bottle as this makes it lighter and helps it stick and soak into the to the tile and grout as opposed to running down it. It was noticeable that the grout colour was mainly intact and it had just needed a good clean on the whole apart from maybe near the cooker which I topped up with new Grout colour in the original shade.

Applying Grout Colourant

Once everything had been rinsed and the grout had dried I was able to apply the grout colourant using my colour applicator (toothbrush). You have to be fairly methodical doing this so it can take a while, you can remove excess colourant by spraying plain water and scrubbing with a white pad (don’t used a coloured pad as you can transfer the dye from the coloured pad to the surface).

Grout colouring Preston Ceramic Wall Tile After

 
 
Source: Refreshing ceramic tile grout in Lancashire

Grout Re-Coloured in Buckinghamshire

We were asked to improve the appearance of this Ceramic tiled floor and Grout installed in a kitchen in Chalfont St Giles which over a few years had become difficult to keep clean and the grout lines had become stained and discoloured.

Ceramic Tile and Grout Before Ceramic Tile and Grout Before

Cleaning Tile and Grout

Our first task on day one was to clean the Ceramic tiles and Grout so we created a diluted 50/50 mixture of tile doctor Pro-Clean and Nanotech UltraClean, the two products combine to provide a very powerful tile friendly alkaline cleaner with tiny sized abrasive particles. This was left to soak into the tile and grout before being agitated and scrubbed with a scrubbing machine running on low speed. We also used stiff grout hand brushes along the grout lines. Once we were happy with the overall condition of the tile and grout it was washed down using clean water and the resultant soiled solution extracted from the floor using a wet vacuum. I’m pleased to say that using this method we were able to return the tile and grout back to its original colour.

Whilst this was a fantastic transformation the grout lines being porous would untreated soon become dirty and discoloured. The only answer to this problem is a permanent colour seal to the grout lines which not only aids the future floor cleaning, but improves the whole appearance of the floor.

Applying the Grout Colour

Before applying a Grout Colour it’s important to ensure the grout is clean of grease and dirt naturally we had just cleaned this floor so this was not a problem I only mention it in case you were considering taking on a similar task yourself.

Once the grout has dried you can start applying the colourant which is a relatively straightforward process of squeezing the product onto a toothbrush and running it onto the grout. Don’t be tempted to use an old toothbrush for this purpose as it may contaminate the colourant leading to discolouration in the finish.

We completed the project the next day using an Aqua Mix sand coloured Grout Colourant; the customer was extremely pleased and commented how whole clean and efficient the process was.

Ceramic Tile and Grout After Ceramic Tile and Grout After

 
 
Source: Tile Cleaining and Grout Re-colouring in Buckinghamshire

Cleaning Tile and Grout in Melton Mowbray

This Ceramic tiled floor was installed in the Kitchen of a house in Melton Mowbray, as you can see from the photographs the tiles were in reasonable condition it was mainly the grout had become discoloured and in need of a deep clean. We do find this with Ceramic and Porcelain tiles, they are very hard wearing and unless you drop an Iron on one they are usually good for a long time; the top layer of grout however is porous and will attract dirt over time if it’s not sealed.

Ceramic Tile and Grout Before

Cleaning Ceramic Tile and Grout

I used a strong solution of Tile Doctor Pro-Clean diluted with hot water and applied it to the floor letting it dwell and soak into the tile and grout before being agitated using a rotary machine fitted with a black scrubbing pad. This worked well to clean the tile but the grout needed more work so we got our knee pads on and hand scrubbed along the grout lines with a stiff brush. The soiled solution was removed using a wet vacuum and floor rinsed with clean water so we could see if there were any areas in need of further attention and repeated the process until we were happy the whole floor.

Grout Sealing

I then left the floor to dry out and came back to seal the grout using Tile Doctor Seal and Go which will protect the grout from staining in the future by adding a barrier to the surface of the grout.

Ceramic Tile and Grout After

I think you will agree from the photographs the floor has been transformed and looks like a new installation.
 
 
Source: Tile and Grout cleaning in Leicestershire

Cleaning and Removing Grout Haze from a Quarry Tiled floor in Kemsing, Kent

The attached pictures are of a Quarry Tiled floor in a kitchen and family room of a cottage in Kemsing, Kent. The cottage was undergoing a full renovation and extension, and the quarry tiled floor was recently installed, however it was not sealed prior to grouting, and a grey grout haze was now sitting across the whole floor. Quarry tiles are highly porous and if not sealed before grouting the grout sitting on the tile soaks in leaving the colour of the grout as a haze over the tile.

Quarry Tile Floor Before

Cleaning Quarry Tiles

There had been a number of tradesmen working constantly on the premises so it was difficult to tell what was grout haze and what was builders mess so I the first job was to give the floor a good clean. For this I used a strong mixture of Tile Doctor Pro-Clean diluted with water in a 3:1 ratio. I also added a squirt of Tile Doctor NanoTech Ultra-Clean which is an abrasive clean cleaner and processed to apply the solution to the floor. I left the solution to dwell on the floor for a short while and then scrubbed the floor using my weighted floor scrubbing machine fitted with a black 17inch scrubbing pad. The cleaning residue was removed using a wet vacuum and we could now see all the grout haze quite clearly.

Quarry Tile Floor Before

Removing Grout Haze from Quarry Tiles

To remove the grout haze one part Tile Doctor Grout Clean-up was mixed with three parts water and poured into a spray bottle; Grout Clean-up is a product specifically designed for removing grout haze. This was then sprayed onto the floor, covering an area of around 1m2 and spread so it covered the grout haze evenly. This was allowed to dwell on the tile for three to four minutes before I agitated the solution by hand with a pan scrubber and water. This was then vacuumed up before I took a scrubbing brush and clean water from another bucket and scrubbed the area, before again vacuuming up. This ensured that all the formula had been cleansed from the floor; this process was repeated across the whole floor, working on 1m2 at a time and then left to dry ready for sealing.

Quarry Tile Floor Before

Sealing Quarry Tiles

The floor was now ready for sealing; Quarry tile floors can accept two types of sealer, a topical sealer or an impregnated sealer. I usually recommend Tile Doctor “Seal & Go” for Quarry tiled floors which is a Topical sealer as it is easier to maintain. On this occasion however the customer wanted to wait until they had completed decorating and was happy to seal the floor themselves, so I gave them advice on what sealers to use and how best to use them and left them to it.

Quarry Tile Floor After Quarry Tile Floor After

 
 
Source: Removing Grout Haze from Quarry Tiles

Quarry Tiled Kitchen Floor Cleaned in Leatherhead

Details below of a Quarry Tiled kitchen floor that were cleaned and sealed for a lady in Leatherhead. As you can see it was quite a large area and the quarry tiles were looking dull and tired, there was some staining to the grout.

Quarry Tile Cleaning Before

Cleaning Kitchen Quarry Tiles

A solution of Tile Doctor Pro-Clean was applied to the floor and left to soak for a short while before being scrubbed in with a rotary machine fitted with a black scrubbing pad. The grout also need attention, unfortunately we don’t have a machine that will get into the grout lines so this had to be manually scrubbed by hand using a grout brush, which as you can imagine took some time to do. The soiled cleaning solution was then removed using a wet vacuum and the floor thoroughly rinsed with water and then left to dry overnight.

Quarry Tile Cleaning Before Zoom Quarry Tile Cleaning After Zoom

Sealing Kitchen Quarry Tiles

When we returned the next day we could see there were some grout lines that we had missed the day before so we set about cleaning those up. Once we were happy with the floor it and it had managed to dry off we sealed the floor using six coats of Tile Doctor Seal and Go which provides surface stain protection to the quarry tile and grout and also leaves a nice deep low sheen on the tile surface. The lady was over the moon with the results and her husband was even happier because it meant he didn’t have to pay out for a new kitchen.

Quarry Tile Cleaning After

 
 
Source: Leatherhead Kitchen Tile and Grout cleaned and Sealed