Shower Tile and Grout Refresh

This Ceramic Tiled shower cubicle in a house in Hale was overdue a deep clean, the Ceramic Tiles were in reasonable condition but the grout lines had discoloured and become stained from the dyes in shampoo’s and soaps and the silicone needed to be replaced.

Shower Refresh Hale Before Cleaning 1

Cleaning Shower Tile and Grout

To clean the grout I decanted a strong 2:1 dilution of Tile Doctor Pro-Clean into a spray bottle and sprayed the solution on the tile and grout working in small sections. I think I’ve mentioned this before but in case you were wondering mixing the cleaner with air makes it lighter and allows it to stick onto vertical surfaces better. The solution was then worked in using a stiff scrubbing brush by hand before being rinsed off with water; this process was repeated until all the tile and grout was clean and then left to dry. If you’re doing this work yourself then you should know that Tile Doctor produces a product that comes with a spray attachment called Oxy Pro that is ready to use and can save you some time.

The next step was to take a sharp knife and remove and replace the silicone strip between the tile and the shower tray.

Grout Colouring

Although the grout was cleaner following the scrubbing it was still showing some staining so to improve it further a white Grout Colourant was applied, fortunately the tiles were large format and the grout lines minimal. The product we use is epoxy based and forms a thin impermeable barrier over the grout so not only does it look good it protects the grout as well; it’s very easily applied using a small brush along the grout lines and you just wipe of the excess so it wasn’t long before the grout was looking like new.

I think you will agree from the photographs the finished result looks like a new installation, certainly my customer was very pleased with job I had done.

Shower Refresh Hale After Cleaning 2

 
 
Source: Manchester Tile and Grout Cleaning

Quarry Tiled Kitchen Floor Cleaned in Leatherhead

Details below of a Quarry Tiled kitchen floor that were cleaned and sealed for a lady in Leatherhead. As you can see it was quite a large area and the quarry tiles were looking dull and tired, there was some staining to the grout.

Quarry Tile Cleaning Before

Cleaning Kitchen Quarry Tiles

A solution of Tile Doctor Pro-Clean was applied to the floor and left to soak for a short while before being scrubbed in with a rotary machine fitted with a black scrubbing pad. The grout also need attention, unfortunately we don’t have a machine that will get into the grout lines so this had to be manually scrubbed by hand using a grout brush, which as you can imagine took some time to do. The soiled cleaning solution was then removed using a wet vacuum and the floor thoroughly rinsed with water and then left to dry overnight.

Quarry Tile Cleaning Before Zoom Quarry Tile Cleaning After Zoom

Sealing Kitchen Quarry Tiles

When we returned the next day we could see there were some grout lines that we had missed the day before so we set about cleaning those up. Once we were happy with the floor it and it had managed to dry off we sealed the floor using six coats of Tile Doctor Seal and Go which provides surface stain protection to the quarry tile and grout and also leaves a nice deep low sheen on the tile surface. The lady was over the moon with the results and her husband was even happier because it meant he didn’t have to pay out for a new kitchen.

Quarry Tile Cleaning After

 
 
Source: Leatherhead Kitchen Tile and Grout cleaned and Sealed

Quarry Tile Flooring Restoration

Quarry Tile Floor in Friston
Details below of An 8m2 Quarry Tiled Floor in the kitchen of an old 18th century farm cottage in the village of Friston, which over time had lost its shine and become dull. This floor like a lot of floors we get asked to maintain had lost it’s sealer over the years and was in need of some Tile Doctor TLC.

Quarry Tile Flooring Before Cleaning Quarry Tile Flooring Before Cleaning
Quarry Tile Flooring Before Restoration

Quarry Tile Cleaning
The floor was thoroughly cleaned using 1 litre of Tile Doctor Pro-Clean, a multi-purpose high-alkaline cleaner, degreaser and stripper created for use on most stone and ceramic tiles in use today. The tiled floor was left to dry overnight ready for sealing the next morning.

Quarry Tile Flooring After Cleaning Quarry Tile Flooring After Cleaning
Quarry Tile Flooring After Restoration

Quarry Tile Floor Sealing
The following day, the tiles were sealed with four coats of Seal & Go, a Tile Doctor product that provides a long lasting stain resistant surface seal and a durable low-sheen finish. You can see the difference in the photographs.
 
 
Source: Quarry Tile Restoration

Cleaning Terracotta Floors

This customer had a terracotta tiled floor in the kitchen, utility room and toilet, which hadn’t been sealed for 8 years and told us that the floor needed full restoration. On full inspection we also found that there was grout loose and missing and it was also different colours.

Terracotta Floor in the Kitchen Terracotta Floor in the Kitchen

The tiles were also stained with olive oil from cooking spillages.

Terracotta Floor in the Kitchen Terracotta Floor in the Kitchen

We started by giving the floor a deep clean by using Tile Doctor Pro-clean and scrubbing with deck brushes to remove all soils and old residue sealers. We then thoroughly rinsed the floor using our truck mounted machine and spinner tool. We had a problem of removing the oil stains from the tile as terracotta is very porous and had absorbed the like a sponge.

So we then applied Tile Doctor Remove and Go to the stained areas then sprayed with a light spray of water to help keep it moist and stop it drying out, we left this solution on the tiles for 90 minutes. After the dwelling time we steamed the floor as we rinsed off the Remove and Go. The next step was to rinse the complete floor with our truck mount cleaning system and a tile cleaning spinner tool. This thoroughly rinses and thoroughly cleans the floor with very hot water and high pressure.

We had to then tackle the grout problem, so we removed all loose and old grout, where needed and re-grouted the floor. This was left to dry for 48 hours to completely dry.

Then we applied 8 coats of Tile Doctor Seal and Go, leaving it to dry for 40 minutes between each coat. We returned the following day and re-coloured the grout with Tile Doctor beige grout re-colourant. This was then left to dry and a further 3 coats of Seal and Go.

Once this had dried we buffed the floor to harden the sealer and polish it. We used a Tile Doctor white pad and rotary cleaning and polishing machine to bring out the shine on the floor as shown in the pictures below:

Terracotta Floor in the Kitchen Terracotta Floor in the Kitchen

The customer was on holiday when we carried out the work, we had been dealing with the manager of the property, who when the customer returned was made to phone me, so the customer could thank me personally.

The customer’s comments were:

“I can’t believe how nice our floor looks and never thought it could look so good! “

They spoke to the manager of their property and have asked him to arrange with me another appointment as they wanted me to clean their courtyard area as well as they were absolutely delighted with their terracotta floors.
 
 
Source: Cleaning Terracotta Floors

Lancaster Grout Colouring

Grout Colouring a Ceramic Floor in Lancaster
Here are some details of a small 4m2 Tile Cleaning and Grout Colouring job we did in a shower room in Lancaster. The tiles were recently laid and unfortunately the 5mm wide grout had discoloured because the tiler had used the same bucket to mix the adhesive with and some of the remnants from that had got into the grout mix. If the tiler had used a separate bucket this wouldn’t have happened. The tiler didn’t know what to do to rectify the problem so Tile Doctor got the call. He had done a good job on the rest of the bathroom and the customer didn’t want to upset him over it any further so she was quite happy to pay me to sort the problem out, as long as it didn’t look false.

Before Grout Colouring

Before Grout Colouring

First I cleaned the grout with the pre-treater spray that comes with the kit and washed off the excess with water. Although the directions recommend leaving the grout to dry for 2 hours I left it for 30 minutes followed by a blast from my heat gun to dry any dark wet spots, this speeds up the process immensely.

Applying the Grout Colouring

Next I applied the Grout Colourant, fortunately the tiles were ceramic and the excess grout colourant came off the tiles very easily where I had got some on by accident. The kit came with a special white abrasive cloth which is excellent at removing excess grout colourant from the tiles. I often find unglazed tiles or stone and even some porcelain tiles are slightly porous on the surface and if the grout colourant gets on to these tiles then it can be quite hard to get off. I find it’s always best to do a test first on a couple of rows, if you get any on the tiles, don’t leave it on for more than 10 to 15 minutes as it sets very hard. Porous stones should always be sealed beforehand as it will make them a lot easier to clean. Its worth noting that the Grout Colourant acts as a barrier and so will never need to be sealed, it’s also completely washable.

Tiled Ceramic Floor After Grout Colouring

Tiled Ceramic Floor After Grout Colouring

 
 
Source: Grout Colouring A Ceramic Tiled Bathroom Floor In Lancaster

DSG Car Showroom Morecambe

Filling the gap in areas where other companies come up short, Tile Doctor Lancashire completed this large 180 m2 Porcelain Floor Grout Colouring job for a Car Showroom in Morecambe.

Car Showroom Grout Colouring - Tile Doctor Commercial

Car Showroom Grout Re-Colouring

Source: Grout Re-Colouring