Removing Mould from Grout in a Shower Cubicle

The photographs below are from the bathroom of a house in the Moston area of Manchester which is primarily residential and only 3 miles away from the city centre. My customer had been primarily concerned with the removal of unsightly mould but was also keen to have the grout in the ceramic tiled shower cubicle given a good deep clean.

Ceramic Tiled Shower Cubicle Before Restoration Moston Ceramic Tiled Shower Cubicle Before Restoration Moston

Cleaning a Ceramic Tiled Shower Cubicle

To clean the Shower Cubicle, I used a strong dilution of Tile Doctor Pro Clean which is a strong alkaline cleaner that works really well on grout. The Pro-Clean solution was decanted into a spray bottle and then sprayed onto the grout lines and left it to dwell. The air in the solution makes it lighter and easier for it to stick to vertical surfaces.

After a few minutes the Pro-Clean was scrubbed in using a stiff grout brush. The tiles were then rinsed with water to remove the soiled solution from the tiles and the process repeated where required.

Although cleaning process was a success there were still a few mould marks left so to tackle these I used Tile Doctor Mould Away spray using the same process of scrubbing and rinsing. The Mould Away spray did the trick for me and I moved on to remove the silicone around the shower cubicle. When removing silicone, you must make sure you get all mouldy silicone out otherwise it can spread from the old to the new.

Ceramic Tiled Shower Cubicle During Restoration Moston

After I had finished removing the silicone I tidied the shower cubicle and used a bit of gentle heat from my heat gun to dry the grout lines and edges where silicone used to be.

Grout Colouring a Ceramic Tiled Shower Cubicle

I used my damp tester to make ensure there was no dampness anywhere around the working area and then moved on to colouring the grout which would give the whole shower a fresh and consistent appearance. On this occasion, I used a White colour from the Tile Doctor range of Grout Colourant’s, it’s an epoxy based colourant that protects and rejuvenate the grout lines.

I had to use 2 coats of colourant to get the best result and then moved on to putting new silicone around the shower base with a high-quality mould resistant silicone. When finished adding fresh silicone I tidied up again and the job was complete.

Ceramic Tiled Shower Cubicle After Restoration Moston Ceramic Tiled Shower After Restoration Moston

I think you can’t argue the shower cubicle was transformed and customer even said it looks better then when it was new; we also fixed few chips for her whilst there and stripped and replaced the silicone around the sink as a bonus.

Ceramic Tiled Sink Grout Before Cleaning Moston Ceramic Tiled Sink After Cleaning Moston

 
 
Source: Ceramic Tile and Grout Cleaning Service in Machester

Treating Mouldy Grout in a Shower Cubicle in Cumbria

Grange-over-Sands is a quaint little town on the Morecambe bay, roughly halfway between Barrow-in-Furness and Kendal in Cumbria. I was recently contacted by a property owner in the area who had heard about Tile Doctor services and was keen to have us restore their tiled shower cubicle which, as you can see from the photos below, had staining and mould on the ceramic tile, grout and silicone sealant.

Shower Cubicle in Grange-over-Sands Before Cleaning

The shower cubicle was looking far from inviting and well in need of a good deep clean. I agreed a quote for cleaning and recolouring of the grout, and was soon on my way to the property to carry out the work.

Shower Cubicle in Grange-over-Sands Before Cleaning

Cleaning and Recolouring a White Tiled Shower Cubicle

I started by cleaning the dirty grout with Tile Doctor Mould Away, which is a fast and effective formula for the removal of mould from silicone and grout. I sprayed the product onto the tile and grout and left it to soak in for five minutes, before scrubbing the area with a stiff brush. I then rinsed the area with water, and repeated the process until the mould and staining had completely disappeared.

To guarantee the overall appearance I had agreed with the owner to apply a grout colourant to the grout. For best results, we recommend a pre-treater is applied to the grout first as it helps bond the grout colour to the Grout. The pre-treater was applied then the whole cubicle was rinsed.

The next step was to carefully strip out the old silicone sealant from around the base of the cubicle using a sharp blade.

Colouring Grout in a Shower Cubicle

The grout needs to be dry to take the colourant so after cleaning and pre-treating I dried the grout with a heat gun on a low setting.

Once I was happy the grout was dry I started the recolouring process using a White colourant from the Tile Doctor range which has ten popular colours to choose from including Charcoal Grey, Cappuccino and Black. This would ensure the grout matched nicely with the rest of the cubicle.

The colourant not only restores the colour, it also rejuvenates and seals the grout joints. The lastly step was to apply fresh white silicone around the base of the cubicle.

Shower Cubicle in Grange-over-Sands After Cleaning

I think you will agree from the photos of the finished result the whole cubicle looks much fresher and that it would be difficult to tell the difference from a new installation.

Shower Cubicle in Grange-over-Sands After Cleaning

 
 
Source: Shower Tile and Grout Cleaning Service in South Cumbria

Refreshing the Appearance of Bathroom Grout

We commonly encounter customers who are struggling to keep their Ceramic tiled shower cubicles clean. Since most people use their showers every day, the tiles and grout inevitably come into contact with shampoos and soaps that can cause staining, discolouration and mould. In fact, it’s not uncommon for property owners to completely give up on trying to clean the tiles, especially as many everyday cleaners are ineffectual, and this allows the situation to worsen over time.

This customer, who lives in Hale Village – known to be one of the UK’s quietest and best kept villages despite being just outside the busy city of Liverpool – was fed up with the state of her tiled shower cubicle and decided to seek professional assistance. I explained that with regular maintenance using suitable products, the tiles could be easily kept clean. I visited the property to show her first hand the results that could be achieved by cleaning and recolouring the grout.

Ceramic bath tiles before refresh Hale Village Ceramic bath tiles before refresh Hale Village

Grout Cleaning and Recolouring Ceramic Bathroom Tiles

The ideal product for cleaning grout that has become affected by mould is Tile Doctor Mould Away, a fast and effective formula that can be directly applied. After applying the Mould Away I allowed it to soak into the grout for 20 minutes, before scrubbing it in with a special handheld brush. I also scrubbed it into the tiles to remove any excess staining caused by coming into contact with shampoos and soaps.

After completing a thorough clean of both the grout and tiles, it was time to remove the old silicone sealant from around the edges of the bath, and replace it with a fresh white sealant. I then opted to recolour the grout to match it with the tiles and the new sealant, doing so carefully with Tile Doctor’s own White Grout Colourant. This is just one of ten different Grout Colourant options we offer. Other options include Charcoal Grey, Black and Cappuccino Brown to much different colour tiles.

Ceramic bath tiles after refresh Hale Village Ceramic bath tiles after refresh Hale Village

The combination of cleaning and recolouring completely refreshed the appearance of this Ceramic tiled shower cubicle, to the point that it almost looks new. Needless to say my customer was very happy, and can see now just how easy it can be to keep these tiles looking good using the right products.
 
 
Source: Bathroom Tile and Grout Cleaning Service in Cheshire

New but Discoloured Grout refreshed in a Warrington Kitchen

It can be amazing and equally frustrating just how quickly grout can become dirty and discoloured. I was recently contacted by a couple in Warrington to see if I could help them with their Ceramic tiled kitchen floor that had only been laid six months earlier. To their dismay, in that short time the grout had become discoloured and difficult to clean. They had given up trying to resolve the situation by themselves and so turned to Tile Doctor for some professional assistance.

Naturally I was happy to assist and so arranged to visit the property to conduct a small cleaning test where I demonstrated how with a combination of the right tools and products I could indeed get the grout lines clean again. Seeing the results of the test, the couple were more than happy to book me to complete the job.

Kitchen tiles before cleaning and grout recolour in Warrington

Grout Cleaning for Dirty Ceramic Tiles

On my return to the property, I repeated the same successful test clean across the entirety of the floor. This involved the application firstly of Tile Doctor Remove and Go, which is a strong cleaner, stripper and degreaser. I scrubbed the product thoroughly into all the grout lines, making sure I did not miss any dirt and stains.

I then started to clean the Ceramic floor tiles using our high alkaline cleaner, Tile Doctor Pro Clean. This was scrubbed into the floor in a similar fashion to the Remove and Go and then rinsed off with plain water extracting the waste water with a Wet Vat. The floor was left to dry over lunchtime.

Recolouring Grout for Ceramic Tiles

In the afternoon, I explained that whilst I could get the grout clean it was only a matter of time before it became dirty again. So, to provide a permanent solution I recommended to the customer that we apply an epoxy Grout Colourant, which adds a protective barrier over the grout. An alternative would have been to apply a Grout Sealer however this is best applied to new grout and in this case would not have guaranteed the uniform appearance required.

Before applying the Grout Colourant, I made sure the grout lines were dry by giving them a quick blast with a heat gun. I then started to colour the grout lines with our White Grout Colourant, which is part of a range made by Tile Doctor and is available in ten popular colours, including Black, Charcoal Grey and even Cappuccino Brown.

The difference made to the floor was quite remarkable. Not only is the grout now a uniform brilliant white, but it should remain so for a long time to come. You can see this yourself in the photograph below!

Kitchen tiles after cleaning and grout recolour in Warrington

 
 
Source: Tile and Grout Cleaning and Restoration Service in West Cheshire

Dealing With Discoloured Shower Cubicle Grout

Shower cubicles can be the most difficult of tiled features to keep clean. Most are exposed to various acid-based soaps and shampoos on a daily basis, allowing mould and general muck to quickly build up along the grout lines and silicone. This leaves the entire area looking quite unappealing. In some cases, the grout lines become stained beyond a point where they can be restored to their original condition, so property owners will typically request to have the grout cut out and replaced however a faster and cheaper method is to have the grout completely recoloured.

Such was the case with this Ceramic tiled shower cubicle at a house in Wigan. It would take a lot to get the cubicle looking great again, having not been cleaned properly for a long time. The property owner decided to contact me for a professional refresh, including cleaning, new silicone sealer and recolouring of the grout.

Ceramic Shower Cubicle Before Refresh Wigan

Cleaning a Ceramic Tiles Shower Cubicle

I started the refresh by applying Tile Doctor Mould Away spray to the tiles and grout, and leaving it to dwell for an hour. As the name of the product suggests, Mould Away is a fast and effective cleaner for the removal of mould from silicone and grout, making it ideal for use on shower cubicles similar to this one. I then rinsed the entire area down with water before scrubbing the grout lines and tiles with a stiff grout brush to remove any remaining mould and lime scale, leaving them looking a lot cleaner.

Colouring Grout in a Ceramic Tiles Shower Cubicle

The cleaning process made a big improvement however the grout was still too stained so after removing the silicone strip from around the base of the shower I proceeded to recolour with our white Grout Colourant. The colourant is painted onto the grout and any excess is wiped of the tile before it dries which both improves the appearance of the grout and seals it in to protect it from further staining. The last step was to apply fresh white silicone along the base of the shower.

Ceramic Shower Cubicle After Refresh Wigan

The customer was very pleased with the refreshed appearance of their shower and you must admit it looks much more inviting now.
 
 
Source: Ceramic Tile Clearing and Restoration Service in Greater Manchester

Refreshing the Grout in a Ceramic Shower Cubicle

Many homeowners will be able to relate to this post about tiled shower cubicles which can become mouldy, grubby, and just plainly unappealing to look at. The reality is that dirt, mould, and stains can be quite easily removed with the right products if addressed on a regular basis. However, many busy homeowners simply don’t have the time, and subsequently the mould problems gradually worsen over time. This is what had happened at this property in Ramsbottom (a town known for its annual Chocolate Festival) – the customer’s Ceramic tiled shower cubicle had not been adequately cleaned in a long time, resulting in severe staining that would prove impossible to remove entirely.

Deep Cleaning a Shower Cubicle In Ramsbottom Before

When the customer contacted me after finding Tile Doctor over the internet, I suggested that I could provide the grout with the best clean possible before re-colouring the grout with a white Grout Colourant to hide the staining and it back to looking similar to its original condition. The customer agreed that this would be the best course of action, and booked me in to complete the work.

Deep Cleaning a Shower Cubicle In Ramsbottom Before

Cleaning Ceramic Tiled Shower Cubicle Grout

The first step in the restoration was to get the grout ready for the new Grout Colourant to be applied. This involved cleaning the grout with Tile Doctor Pre-Treat Cleaner, which successfully removed the various dirt, soil, soap scum and hard water deposits that had built up after plenty of exposure to acidic shampoos and soaps. Getting the grout joints clean allows the colourant to form a better bond with the grout.

The Pre-Treat Cleaner was sprayed onto the grout and left to dwell for roughly five minutes before being agitated with a grout brush. Next, I rinsed the grout with water and removed the old and mouldy silicone around the shower cubicle.

Colouring Grout and Siliconing for a Ceramic Tiled Shower Cubicle

After running tests I discovered a few damp issues, but these were quickly resolved with the help of my heat gun. With the grout now ready to be coloured, I applied two coats of Tile Doctor’s white Grout Colourant, allowing the first coat to dry before applying the second.

Deep Cleaning a Shower Cubicle In Ramsbottom After

The Grout Colourant is an epoxy-based product that seals and rejuvenates the grout, protecting it against future staining and making it easy to clean in the future. After completing the grout colouring I cleaned up the area – including removing any excess product – and then applied fresh silicone in a matching white around the base of the shower cubicle.

Deep Cleaning a Shower Cubicle In Ramsbottom After

As you can see from the photographs, the appearance of the shower cubicle was transformed by the new Colourant. My customer even left the following comment on the Tile Doctor feedback system:

“Tony was polite punctual and efficient. We are very happy with his work!”
 
 
Source: Shower Tile Grout Cleaning and Colouring Service in Derbyshire

Achieving the Consistent Appearance of old Grout using Grout Colourant

The task of keeping these white Ceramic Kitchen and Conservatory tiles clean was proving very challenging for this customer, who lives in the town of Somerton in Somerset. Somerton is known for its bustling market, which has supposedly been run on a weekly basis since the Middle Ages, and its famous ‘Market Cross’ at the centre of the beautiful marketplace is a popular tourist attraction for visitors to the West Country.

It probably comes as no surprise to anyone that white tiles are often more difficult to keep clean than others. However, in this case, rather than being badly marked or damaged, these Ceramic tiles had become dirty due to the surface being pitted rather than smooth which trapped ground in marks from spills and dirty footprints etc. The pitted rough surface is very characteristic and provides better grip however they do trap dirt are therefore more difficult to keep clean.

The grout had also suffered over the years, losing a lot of its colour in the process so as well as cleaning the tiles we agreed to give the grout a really deep clean and also to colour the grout to make it more uniform.

Cleaning a Pitted Ceramic Tiled Floor

To clean the tiles, I firstly created a strong diluted of Tile Doctor Pro Clean and applied it liberally across the entire floor, leaving it to dwell and soak into the tile for a short period in order to soften the ingrained dirt. I then used my heavy weight rotary machine fitted with a black scrubbing pad to agitate the solution and break down the muck.

Once satisfied with the condition of the tiles I turned my attention to the grout lines, cleaning them carefully by hand using a stiff tile cleaning brush and the same solution of Pro Clean and water. This provided a deep, penetrating that clean that left the grout lines clean and free from the dirt and grease that had dulled their appearance for so long.

With some great results achieved through the cleaning, I rinsed the whole floor to wash away any leftover Pro-Clean and left it to dry fully overnight.

Ceramic Tiles Somerton After Cleaning but Before Grout Colouring

Recolouring Grout for a Ceramic Tiled Floor

I returned to the property the next day to check on the floor and after ensuring the floor was completely dry, proceeded to recolour the grout lines using Tile Doctor’s Grout Colourant. Our Grout Colourants are a waterborne epoxy that recolours, seals and rejuvenates existing grout joints and is available in ten different colours ranging from white to dark greys. The scrubbing with Pro-Clean the day before would also ensure the surface of the grout was clean and would make a good surface for the colourant to bond with.

Since in the past the grout lines had undergone a number of repairs, the existing colour was a mix of different greys. It made most sense then that they picked our ‘Natural Grey’ Grout Colourant for me to use. I painted the Colourant on carefully and waited for 30 minutes before removing any excess, leaving the grout lines perfectly covered in a uniform colour.

Ceramic Tiles Somerton After Cleaning and Grout Colouring

The difference was really noticeable and the property owner was really happy with the results. As you can see from the photos, the new grey Colourant really made the grout lines stand out against the clean white Ceramic tiles. Another satisfied customer.
 
 
Source: Grout Cleaning and Colouring Service in Somerset

Completly changing the Appearance of Ceramic Tile and Grout in Flintshire

Moving into a new home is a stressful but rewarding experience. This customer had just recently moved into a property in the neighbouring and historic Flintshire town of Mold, and was keen to make some renovations.

High on the agenda was the restoration of a large number of Ceramic floor tiles spread throughout multiple downstairs rooms. Although undecided as to whether to keep the tiles for the long-term or have them removed, the customer did resolve to have them professionally cleaned, especially since the previous owner had left the grout in a miserable state.

Ceramic Tiled Floor Before Cleaning in Mould

Upon initial inspection I noticed that the previous owner had attempted to put more grout on top of the existing one in some areas, the problem with this being that the two groups were of different colours. This left the grout looking inconsistent and dirtier than it actually was. I mentioned to the customer that I could re-colour the grout for them after cleaning the floor and that it would be the best solution in this situation.

Ceramic Tiled Floor Before Cleaning in Mould

Cleaning and Colouring Ceramic Tiled Floor Grout

As mentioned, the tiles themselves needed a deep clean, and so I set about applying a strong dilution of Tile Doctor Pro Clean liberally over the floor and leaving it to dwell for a short period. This allows the product, a high alkaline cleaner suitable for use on most natural stone floors, to seep into the pores of the stone to lift out and dissolve ingrained dirt and stains. Once I had allowed it to dwell I scrubbed the product into the tiles using a black pad fitted to a rotary machine.

Of course I also paid special attention to the grout lines, carefully cleaning them using more Pro Clean. With some floors I usually give the floor an acid wash at this with Tile Doctor Grout Clean Up to remove grout smears and mineral salt deposits but this was not necessary on this particular occasion.

Ceramic Tiled Floor After Cleaning in Mould

Once I had cleaned the entire floor I gave it a thorough rinse with water which was then extracted using a wet vacuum before leaving the floor to dry for two hours assisted with an air mover to speed up the process. When happy that the tiles were completely dry and ready to be re-coloured I went ahead and carefully applied a new black Grout Colourant that matched very well with the natural colour of the stone, giving the whole floor a smarter appearance.

Ceramic Tiled Floor After Cleaning in Mould

The customer was really pleased with the result and left some nice feedback on the job as a whole:

“Excellent experience all round, from initial consultation through to colour advice and scheduling work. Cannot speak highly enough of Joe, thoroughly professional and an amazing result. Highly recommended.”
 
 
Source: Ceramic Tile and Stone Restoration Service in Shropshire

Applying Charcoal Grey Grout Colourant

Here’s a quick grout cleaning and re-colouring job I completed in the town of Canvey Island, Essex. Canvey Island lies on the south east coast, and lies just above sea level which in my job is always worth noting as the area can be prone to flooding. This wasn’t the problem here though, simply put, my client was unhappy with the colour of their grout, and wanted it re-coloured to a darker shade to match the grey Ceramic floor tiles.

Cleaning the grout before re-colouring is essential because, as many readers are probably well aware, grouts are porous and therefore can very easily absorb dirt and grease. Most often this will result in grout discolouration if not dealt with promptly.

Ceramic tiles before cleaning and colouring in canvey island

Cleaning and Re-Colouring the grout lines of a Ceramic tiled floor

So, as mentioned above the first step in the re-colouring process involved cleaning the grout lines. For this Tile Doctor has a special Pre-Treat Cleaner which is sprayed on and scrubbed into the grout to both remove any existing dirt and also to prepare the grout joints for a superior bond with the Grout Colourant. Once complete the grout lines looked clean and refreshed.

To clean the ceramic I diluted one part Tile Doctor Pro-Clean to three parts water, and used it to wash down the Ceramic tiles, leaving a consistent level of cleanliness across the entire floor. I then rinsed the floor with water which was then extracted using a wet vacuum and waited for 3 hours for the floor to dry.

Once dry, I began the process of applying the Charcoal Grey (as chosen by the client) Grout Colourant to the grout lines. As well as changing the colour the colourant also forms a barrier over the grout sealing it in and protecting it from future staining for years to come.

Then, once dry, the floor was given another quick clean using a light spray of water and a white buffing pad, resulting in an aesthetically pleasing sheen finish. My client was very happy with the outcome and now has the floor they wanted.

Ceramic tiles after cleaning and colouring in canvey island

 
 
Source: Tile, Stone, Grout Cleaning and Colouring service in South-Essex

Shower Cubicle Grout Refresh

The photographs below were taken at a private residence in the town of Stafford, the owner of the house was unhappy with the state of the grout lines in their ceramic tiled shower which had, over time, had become grey and stained. As you cans see from the photograph, the whole area in general was very tired looking. I recommended a grout clean, colouring and seal to get the shower back to looking its best. My client was happy with me to proceed and I promptly began the work.

Grout Colouring Ceramic shower tiled cubicle in stafford before

Grout Colouring including Prep

My first task was to clean the grout using a grout colouring pre-treater which cleans and prepares the grout joints to make a better bond with the colourant. The tiles were then given a rinse and dried before I stripped out the old sealant strip between the tiles and shower tray.

My next task was to carefully apply a white Grout Colourant along the grout lines using an applicator brush. The colourant is basically painted onto the grout and any excess is wiped off the adjacent tile before it dries. The colourant, which is available in a range of shades, is an epoxy based product that both recolours and seals the grout lines to provide protection against dirt and stains.

To finish off the job I applied fresh sealant between the shower tray and bottom row of tiles in a matching white. The whole shower took on a much fresher appearance after I finished and looked transformed.

Grout Colouring Ceramic shower tiled cubicle in stafford after

My client contacted me two weeks after I completed the job to happily inform me that my work had actually solved a leakage problem that have been affecting the shower cubicle. With the addition of a robust clean, colouring and seal, my client was very pleased with the results.
 
 
Source: Professional Tile, Stone and Grout cleaning and maintenance services in Staffordshire

Refreshing the Appearance of Grout

Photographs below of a Ceramic tiled floor in the kitchen of a house in the village of Houghton on the Hill near Leicester. The Ceramic tiles were fine but not unusually the grout had darkened substantially and would need to be deep cleaned to get it fresh again.

Ceramic Tile Before Cleaning Houghton on the hill

Cleaning Tile and Grout

The grout was badly stained so I decided to go with a strong dilution of Tile Doctor Remove and Go which we normally use for removing sealers but is also a very powerful cleaning product. It was run along the grout lines and tile and left to soak in before being scrubbed in with a black pad fitted to a rotary floor machine. The floor was then washed down with clean water and the process repeated until the grout was back to its original condition; the ceramic tiles looked much cleaner as well.

Sealing Grout

The tile and grout was left to dry and then then grout was sealed using Tile Doctor Ultra Seal which is a natural look sealer that I usually use on Travertine but works equally well on grout. You have to remember that the top layer of grout is actually porous and will attract dirt if left un-sealed, sealing it will ensure it keeps its appearance for much longer.

Ceramic Tile After Cleaning Houghton on the hill

 
 
Source: Tile, Stone and Grout Maintenance and Restoration in Leicestershire

Dealing with Darkened Grout

This was a straight forward Grout Colouring job at a house in the market town of Tamworth, Staffordshire. The tiles had been installed with a white grout and over the years the grout had become darker as the dirt had become ingrained into the porous top layer. This is often the case with Porcelain and Ceramic tiles whose looks always outlive that of the grout.

Grout Colour Before Tamworth Grout Colour Before Tamworth

Cleaning and Colouring Grout

The customer was keen to get the grouting looking the same as it was when first installed and so with that aim in mind a dilution of Tile Doctor Pro-Clean was applied and scrubbed into the grout lines and then washed off with water. Pro-Clean is a strong alkaline cleaning product that does a good job cleaning up grout however it can only do so much and in this case although it made a difference there were many areas which were too stained.

The next step was to apply a grout colouring product, they come in a number of different colours and the best match to the original colour was Ivory. The Pro-Clean had already prepared the surface so no need to use a pre-treater, it was just a question of waiting for the grout to dry and then apply the colourant.

Applying grout colourant is fiddly work but you do get the pleasure of watching the floor become slowly transformed, also the colourant works as a sealant which will prevent staining and make the grout very easy to clean going forward.

Grout Colour After Tamworth Grout Colour After Tamworth

As you can see the floor looks like new and the customer was very happy.
 
 
Source: Tile, Stone and Grout Maintenance Service in Staffordshire

Using Tile Doctor Mould Away

This shower cubicle was installed in the main bathroom of a house in Bishopton where the grout had become quite grubby and the Ceramic tiles were looking quite dull. The owner was thinking about re-tiling the bathroom and thought they would give us a call first to see if we could refresh the look without the expense.

Gruby Ceramic Tiled Shower in Bishopton Before Gruby Ceramic Tiled Shower in Bishopton Before

Cleaning Ceramic Tile and Grout

We started by spraying the tiles with Tile Doctor Oxy-Pro which is a strong high-alkaline cleaner especially formulated and packaged for cleaning showers. The spray delivery is important as mixing the cleaning product with air makes it lighter and helps it cling to the tile and grout. The Oxy-Pro was left to soak into the tiles for around 15 minutes before being scrubbed into the tile and grout using a stiff grout brush. This action cleaned up the grout and tile nicely removing stains from shampoos and soaps etc.

Removing Mould from Grout

The grout was looking much improved but there was however some evidence of mould remaining which needed dealing with. To tackle this we used Tile Doctor Mould Away which is designed to remove mould off Silicone and Grout. It’s very easy to use, you simply spray the Silicone or Grout to be treated with Mould Away then leave to soak in for five minutes and then scrub with a brush and rinse with water repeating the process until the mould has disappeared.

Gruby Ceramic Tiled Shower in Bishopton After Gruby Ceramic Tiled Shower in Bishopton After

It took a fair amount of manual effort but the results were well worth it as you can see.
 
 
Source: Expert Ceramic Tile Maintenance advice

Shower Tile and Grout Refresh

This Ceramic Tiled shower cubicle in a house in Hale was overdue a deep clean, the Ceramic Tiles were in reasonable condition but the grout lines had discoloured and become stained from the dyes in shampoo’s and soaps and the silicone needed to be replaced.

Shower Refresh Hale Before Cleaning 1

Cleaning Shower Tile and Grout

To clean the grout I decanted a strong 2:1 dilution of Tile Doctor Pro-Clean into a spray bottle and sprayed the solution on the tile and grout working in small sections. I think I’ve mentioned this before but in case you were wondering mixing the cleaner with air makes it lighter and allows it to stick onto vertical surfaces better. The solution was then worked in using a stiff scrubbing brush by hand before being rinsed off with water; this process was repeated until all the tile and grout was clean and then left to dry. If you’re doing this work yourself then you should know that Tile Doctor produces a product that comes with a spray attachment called Oxy Pro that is ready to use and can save you some time.

The next step was to take a sharp knife and remove and replace the silicone strip between the tile and the shower tray.

Grout Colouring

Although the grout was cleaner following the scrubbing it was still showing some staining so to improve it further a white Grout Colourant was applied, fortunately the tiles were large format and the grout lines minimal. The product we use is epoxy based and forms a thin impermeable barrier over the grout so not only does it look good it protects the grout as well; it’s very easily applied using a small brush along the grout lines and you just wipe of the excess so it wasn’t long before the grout was looking like new.

I think you will agree from the photographs the finished result looks like a new installation, certainly my customer was very pleased with job I had done.

Shower Refresh Hale After Cleaning 2

 
 
Source: Manchester Tile and Grout Cleaning

Dirty Grout Problems Resolved

This Ceramic tiled family bathroom with shower was installed at house in Leighton Buzzard and was in need of rejuvenation. You can see from the photograph below that the tiles were in reasonable condition but the grout had become ingrained with dirt which is not unknown as the top layer of grout is porous and will discolour over time if not protected.

Cleaning Ceramic Tile and Grout

The Ceramic tiles and grout were treated using a strong 2:1 dilution of Tile Doctor Pro-Clean mixed 50/50 with Nanotech Ultraclean which combines a highly powerful Tile and Grout cleaning product with tiny abrasive particles. For vertical tiled surfaces I recommend the mixture is decanted into a bottle with a trigger spray attachment which when sprayed onto the wall allows the cleaner to mix with air making it lighter and allowing it to stick better. The solution was then worked in using a stiff scrubbing brush by hand before being rinsed off with water; this process was repeated a number of times until we had managed to clean all the areas and then left to dry.

Ceramic-Tiled-Shower-Before-and-After-Leighton-Buzzard

Sealing Grout

The grout was dried and the sealed with a couple of coats of Tile Doctor Grout Sealer which forms a protective barrier over the porous grout and keeps it looking good for longer. Most sealers can be used on grout (check the label to confirm) but for best results use a spray bottle as mixing the sealer with air improves its ability to stick to a vertical surface.
 
 
Source: Ceramic Tile and Grout cleaning tips

Grout Cleaning and Colouring in Preston, Lancashire

Oddly Enough I had sold these Ceramic tiles to the customer in Preston when I used to work at a local Tile Shop many years prior. I had also been back to clean and seal the grout on his floor tiles originally in 2007 and then again in January 2010 when we used a Grout Colourant on them. It’s nice to get called back like this as it shows they appreciate the service you provide; for this visit the request was to freshen up the floor tiles and also the Ceramic Kitchen wall tile and Grout which had become ingrained with Grease from the cooker.

Grout colouring Preston Ceramic Wall Tile Before

Cleaning Tile and Grout

The total area was approximately 25m2 and it took me a day and half to give the Tile and Grout a deep clean. For the most part I used Tile Doctor Pro-Clean but for the wall tiles where Grout Colourant has been applied I used Tile Doctor OxyPro which is a ready to use Tile and Grout cleaner that comes in a spray bottle, when applying any liquid to a wall its best to mix it with air in a spray bottle as this makes it lighter and helps it stick and soak into the to the tile and grout as opposed to running down it. It was noticeable that the grout colour was mainly intact and it had just needed a good clean on the whole apart from maybe near the cooker which I topped up with new Grout colour in the original shade.

Applying Grout Colourant

Once everything had been rinsed and the grout had dried I was able to apply the grout colourant using my colour applicator (toothbrush). You have to be fairly methodical doing this so it can take a while, you can remove excess colourant by spraying plain water and scrubbing with a white pad (don’t used a coloured pad as you can transfer the dye from the coloured pad to the surface).

Grout colouring Preston Ceramic Wall Tile After

 
 
Source: Refreshing ceramic tile grout in Lancashire